d4ae308f9f
cmsis: implement srst_set_val()
2021-10-31 12:55:41 +01:00
166eb3ee3e
cmsis_dap: Always transfer 65 bytes with hid_read|write()
...
CMSIS-DAP Dragonprobe works on some devices. E.g. it does not work
on NUCLEO-F103
2021-10-31 12:55:41 +01:00
b343ebe06f
cmsis-dap/linux: Link against libhidapi-hidraw
...
libhidapi-libusb detaches a kernel module but does not reattach again.
This may wrack interaction with other programs using hidapi.
2021-10-31 12:55:41 +01:00
d144f9d54b
adiv5: CMSIS DAP transactions are slow but work in principle
...
Slowness results in strange STM32F767 DHCSR implementation to nearly never
halt in the given 2 second period when F767 is sleeping most of the time.
2021-10-31 12:55:41 +01:00
761e0230d4
cmsis-dap: Print messages when transfers fail.
...
Expect signal integrity errors when using jumper cables. Often probes switch
the SWJ GPIO with highest speed, resulting in possible reflections. Additional
ground wires may help. If there is isolation between probe and targets,
additional ground wires are a must or ground shift will wrack the transfer!
2021-10-31 12:55:41 +01:00
39fbffd3d2
stlinkv2: Fix low access to AP registers.
2021-10-31 12:55:41 +01:00
c13778139f
adiv5/hosted: Export the BMP_TYPE in DP.
2021-10-31 12:55:41 +01:00
b7e7aa3f9a
adiv5: Either use only LL functions in cortexm_initial_halt or no LL at all.
...
Platform implementation may disturb ADIV5_AP_DRW and so low_read DHCSR may
give values other from registers
2021-10-31 12:55:41 +01:00
485105221e
dap: Always work on a copy of the buffer when calling dbg_dap_cmd() in a loop
...
A better solution would use seperate buffers for dbg_dap_cmd. But as WAIT is
already handled in DAP, cahnces are low that loop re-entry is needed.
2021-10-31 12:55:41 +01:00
397fbd5749
cmsis: Only cmsis internal use must differentiate between HID and Bulk access
...
Missing DAP_SWD_SEQUENCE may eventually need a distinction visible from
outside later.
2021-10-31 12:55:41 +01:00
7b1eb6e6e3
bmp_libusb: reset type on every device.
2021-10-31 12:53:47 +01:00
80064c18a9
bmp_libusb: Fix CMSIS-DAP related memory leak.
2021-10-31 11:13:34 +01:00
8845a22226
stm32l4: Use targetid when available.
...
Fixes STM32U5 from crashing.
2021-10-31 11:13:34 +01:00
c4b6b42dcf
stlinkv2: Read targetid on DPv2 devices.
2021-10-31 11:13:34 +01:00
5dafc0828c
SWD: Remove excessive line resets.
2021-10-31 11:12:46 +01:00
e7e1bfdb53
mpsse: Fix using 60 MHz clock on fast devices.
2021-10-30 13:55:57 +02:00
99a5fdb6f8
bmp_remote: Better error propagation.
...
Negative values from platform_buffer_read are errors too!
2021-10-30 13:55:57 +02:00
f4117aa1b4
cdcacm: Use the USB strings.
2021-10-30 13:55:57 +02:00
f28f05952f
stlink: Add another STLINK-V3 ID.
2021-10-30 13:55:57 +02:00
7307f086c6
Support for STM32WB55 ( #942 )
...
* add STM32WB55 support
2021-10-30 13:01:06 +02:00
e1a928beb1
Fixes to compile with gcc11 #925
...
Target code changes are pure for formal correctness and not tested!
2021-10-10 15:59:57 +02:00
e2d3161442
Removed -S message as debugger selection option since it is used for reading bytes
2021-10-09 21:38:48 +02:00
59282b6f66
Fixed typography
2021-10-09 21:18:52 +02:00
7274f55ff4
Fixed return value of hosted blackmagic in erase mode
2021-10-09 21:17:58 +02:00
3f54fba986
HOSTED_BMP_ONLY=0 by default on Linux.
...
The user is warned about missing dependencies.
2021-10-09 21:14:52 +02:00
7ccbdd98c0
hosted/dap: Copy command buffer in wait/retry loop.
...
The same buffer is used for both command and response, causing part of
the command to be overwritten before it’s retried. Solve this by saving
and restoring a copy of the command before retrying.
2021-10-05 23:21:07 +02:00
f69f29a660
f4discovery/blackpill: fix usbusart
2021-10-01 00:10:03 +02:00
b076d5cea1
stm32f1: Check if unlock failed and propagate error.
2021-09-22 21:41:43 +02:00
554e34517e
Better reporting when monitor command fails.
2021-09-22 21:41:43 +02:00
9e98cfa220
adiv5: Remove leftover debug output.
2021-09-22 21:41:43 +02:00
64f756d627
Test voltage on VREF before enabling target power (mon tpwr), to avoid potential power conflict.
2021-09-22 20:45:18 +02:00
356325f563
ftdi_bmp: Fix bit select.
2021-09-22 15:16:20 +02:00
79066c950f
bmp_libusb: Remove duplicated libusb_init.
...
Thanks to Red Liu for noticing
2021-09-22 15:16:20 +02:00
9ebc44bcea
Make more functions static.
2021-09-22 15:16:20 +02:00
db1f13db25
remote: Packets may be larger than 256 bytes.
2021-09-22 15:16:20 +02:00
88cce08ce4
hosted: Fix "monitor version"
2021-09-22 15:16:20 +02:00
da15cc3cb7
remote_jtagtap: Fix memory corruption in jtagtap_tdi_tdo_seq
2021-09-22 15:16:20 +02:00
a93e57e112
ftdi: Fixed wrong direction report in DEBUG.
2021-09-22 15:16:20 +02:00
9de69bb3ab
Adiv5/Initial halt: More fixes for dd28fa5743. #925
...
Stlink does not like low level access and aborts with STLINK_SWD_DP_ERROR.
Either our implementation still has faults or stlink can not handle
MINDP devices with BMP/Firmware also seemm not to like low level access,
either du to some hidden error in BMP or by design
2021-09-22 15:16:20 +02:00
a9854e9b37
adiv5: Fix the MINDP case introduced with dd28fa5743 #925
2021-09-16 12:39:26 +02:00
01583560cd
hosted: Update Readme.md to use HOSTED_BMP_ONLY
2021-09-16 11:02:31 +02:00
f66caa0d29
add some more nxp s32k14x variants
...
the sdid bits correspond to s32k14x as well as s32k11x but i only have
access to the k14x variants so didn't bother w/ the k11x variants.
the memory/flash sizes also can come from the sdid bits, but the
splits still need to come from a lookup.
2021-09-13 23:01:05 +02:00
95288bcf75
fix a size format warning
2021-09-13 23:01:05 +02:00
e58b7d623b
crc32: Abort generic_crc32 with error from target_mem_read
...
Use larger chunks for hosted to speed up. Send pure NULL as line keep-alive.
2021-09-07 10:57:17 +02:00
ff79108f66
cl_utils: Increase worksize for increased speed.
...
H743 reads 2 MB in ~23 vs 27 seconds
2021-09-07 10:57:17 +02:00
a76a559656
pc/platform_delay: Wait ms and not us!
2021-09-07 10:57:17 +02:00
dd28fa5743
adiv5: Tighten up loop to initial halt cortexm
...
Use TRNCNT when available.
Now the F767 with the NutOS 300 ms sleep example with the one ms tick is
halted even in hosted after few ms.
2021-09-04 21:15:07 +02:00
a297c8c8ad
hosted/Makefile.inc: Use gcc to build hosted, if not advised otherwise
2021-09-04 21:15:07 +02:00
698cfeb1f4
bmp_serial: Nag MACOS programmer to implement find_debuggers!
2021-09-04 21:15:07 +02:00
35687018eb
Escape '*' in responses of the Remote Serial Protocol, to avoid that it is interpreted as the start of an RLE sequence
2021-08-31 15:44:17 +02:00
863a41daac
adiv5_swdp: Initialize initial_dp with the definition
2021-08-15 16:43:29 +02:00
49122b50b6
hosted: Make HOSTED_BMP_ONLY the default.
...
Hopefully more people will use it when reporting errors!
2021-08-15 16:43:29 +02:00
2fcd4a878a
ftdi_bmp.h: Fix error when compiling with HOSTED_BMP_ONLY=1
2021-08-15 16:43:29 +02:00
6308506276
jtag: Make jtag_devs argument to jtag_handler.
2021-08-15 16:43:29 +02:00
6dff2a9f31
target: target_error_check now defaults to not indicate error.
...
Remove unneeded nop_function from efm32
2021-08-15 16:43:29 +02:00
f7670fcd44
ftdi_bmp: Add verbosity for libftdi_jtagtap_tdi_tdo_seq()
2021-08-15 16:43:29 +02:00
3df692ecb2
adiv5_swdp_scan: If SWD scan fails, try a JTAG scan.
2021-08-15 16:43:29 +02:00
5c8e277663
hosted/dap: Fix tdi_tdo_seq.
2021-08-15 16:43:29 +02:00
2d4a503135
jtag_scan: Rework chain detection
...
Fixme: stlinkv2/hosted probably does only handle STM devices. Check if
jtag_devs.c really needed.
2021-08-15 16:43:29 +02:00
e1a1865de9
remote/jtagtap_tdi_tdo_seq: Split up large transactions.
...
FIXME: One remote transaction still can only do up to 64 ticks, leaving
room for speed enhancement with larger transactions.
Firmware assumes (1LL << 65) == 0LL !
2021-08-15 16:43:29 +02:00
8084a75634
cl_utils: Allow Hardware reset from the command line
2021-08-15 16:43:29 +02:00
36836d0746
ftdi_bmp: Fix setting bits and FTDIJTAG srst.
2021-08-15 16:43:29 +02:00
cfdf55855e
ftdi_bmp: Export and use reset functions.
2021-08-15 16:43:29 +02:00
1845d71f00
jtag_scan: Deliver full idcode to the handler.
2021-08-15 16:43:29 +02:00
0d78331149
remote/jtag_tdi_tdo_seq: Fix wrong bitmask calculation.
2021-08-15 16:43:29 +02:00
c7bc4b6a5d
Bug fix in Flash erase function for LPC MCUs.
2021-08-13 16:18:53 +02:00
5eb43a1ddb
platforms: stm32f4x1 blackpillv2 as variant of f4discovery
...
Compile as make PROBE_HOST=f4discovery BLACKPILL=1
2021-08-13 16:18:05 +02:00
be534a9c5e
Turn error LED off after successful attach to target (error LED blinks on 'target lost').
2021-08-13 16:10:37 +02:00
72bd825a60
Add support for NXP LPC11xx XL series, add 'readuid' command for some MCUs of the LPC11xx series where it was missing; add comments mapping Device IDs to part descriptions.
2021-07-31 16:08:34 +02:00
6d6a67b44b
timeout: Make sure we wait at least the period requested ( #900 , #902 )
...
Fixes bug introduced with last commit( Recover from bad AP access)
Let STM32 timers run at 100 Hz against 10 Hz before.
Programming STM32F103 failed random (#900 ) with 20 ms timeout requested
against the 100 ms timeout granularity provided up to now.
STM32 Firmware only ticked at 10 hertz, so the sequence "low_access",
"set timeout", "send out 8 bit command", "read 3 bit result" when
reading "wait" and timer increment tick happening during that sequence
will already hits the timeout even so only mininal time has elapsed
and not the requested timeout.
2021-07-27 10:59:03 +02:00
0c63903071
adiv5: Recover from bad AP access.
...
E.g. AP1 on a STM32WLE5 points to a ROM table, but access to the ROM table
via AP1 hangs forever.
- Substantial reduce timeout when wait for a response. Valid access should
succeed fast.
- Abort AP access to free DP for other accesses
- Don't throw exception, only set dp->fault
- React on higher level
2021-07-15 15:06:54 +02:00
b887a8d355
stm32: Portability changes
...
Allow to compile on STM32F0 platform too.
2021-07-15 15:06:54 +02:00
3cfd8226ba
bmp_libusb: Check only for cmsis_dap if no cable has been found yet.
2021-06-18 11:44:50 +02:00
a0dbb2a787
Merge pull request #896 from RadinnAB/for-upstream
...
Add nRF51 erase UICR command and fix some warnings
2021-06-07 17:43:56 +02:00
ea4b232996
Fix de83dbb: duplicate BMP_MODE_FLASH_VERIFY -> BMP_MODE_FLASH_WRITE_VERIFY
2021-06-07 17:29:41 +02:00
5ea01030e2
Add nRF51 command for (only) erasing the UICR registers
...
Original implementation by: Benjamin Vedder <benjamin@vedder.se>
2021-06-07 13:50:36 +02:00
d987a8dd8c
Add define to allow platform override of debug printf function
2021-06-04 06:58:29 +02:00
4b8c4990dc
Fix warning about unused variable in adiv5.c
...
This happens if the platform has debugging support but debugging
is not enabled.
2021-06-03 12:56:41 +02:00
711a87f7ba
Fix some warnings when compiling with -Wshadow
...
There are still a few more places that would need to be corrected
before -Wshadow could be added by default.
2021-06-03 12:55:28 +02:00
53f022d29b
Require semicolon after debug log statements
...
This also fixes a warning about an empty body in cortexm.c
if PLATFORM_HAS_DEBUG is defined but debugging is not enabled:
if (platform_timeout_is_expired(&to))
DEBUG_WARN("Reset seem to be stuck low!\n");
2021-06-03 12:52:07 +02:00
04eab8e1f8
Add guard around _GNU_SOURCE define
...
This avoids warnings if the define has already been set by the
build system.
2021-06-03 12:51:27 +02:00
2a0d608b07
hosted: Fix last commit
...
-Wno-format-truncation may not be understood by all systems
2021-06-01 18:42:37 +02:00
1b49823f64
Fix hosted compile on MacOS. hidapi-libusb has a different name
2021-06-01 16:58:25 +02:00
de83dbb7e2
cl-utils: Fix bug introduced with 5288eef617
...
Always use the file size for write and verify.
2021-06-01 16:23:19 +02:00
c0437e7b25
bmp_serial: Autodetect more BMP string variants.
2021-06-01 16:23:19 +02:00
891633322a
lpc: Care for protected pages on LPC80x devices.
2021-06-01 16:23:19 +02:00
f7b4697280
lpc11xx/lpc8c04: Do not expose two top system flash sectors.
2021-06-01 16:23:19 +02:00
42ebcac329
efm32_devices: Rearrange struct efm32_device_t to save flash space.
2021-06-01 16:23:19 +02:00
21a702dc1e
lpc: More verbosity and more definitions
2021-06-01 16:23:19 +02:00
6454d0bc96
bmp_libusb: Invalidate manufacturer and product in case libusb_get_string_descriptor_ascii fails.
...
Prevent more false detections
2021-05-20 12:06:56 +02:00
7f1a560288
stm32/usbuart: Clear USART_ICR if provided.
...
Otherwise endless interrupts happened.
2021-05-20 12:06:56 +02:00
90534b3cf6
stm32: portability enhancements
...
Needed for e.g. stlinkv3
2021-05-20 12:06:56 +02:00
87acd99fe4
cortexm: For Cortex-M0+ devices, probe also for lpc11 to detect LPC80 #884
2021-05-18 12:24:00 +02:00
cb4cff2c71
hosted/ftdi: Compare only for length of the string given in the header
...
Devices may have added version like "Tigard V1.1" vs "Tigard"
2021-05-18 12:24:00 +02:00
c3fd198f0d
bmp_libusb: Reject non-BMP devices with VID 1d50.
2021-05-18 12:24:00 +02:00
36ad6efc6f
cmsis_dap.h: Fix wrong leftover argument.
2021-05-16 17:17:33 +02:00
f0dd8c9517
cl_utils: List -l option in the help.
2021-05-16 17:17:33 +02:00
517d5b5b31
rp: Show spinner only when called from monitor command.
2021-05-16 11:26:14 +02:00
0ab10fee0b
rp: Increase timeout for flash_range_program
...
If the RP2040 is using the ring oscilator (ROSC) rather than the crystal
oscilator (XOSC) then flashing program will take much longer. As the XOSC is not
enabled at boot we should not assume it will be enabled before the debugger is
connected (or indeed at all), thus should use the longer timeout during load
commands.
2021-05-16 11:26:14 +02:00
ff30259354
rp: Add more debug logging during flash
2021-05-16 11:26:14 +02:00
e453740aca
rp: Increase spinner timeout to 500ms
...
Increasing spinner timeout to 500 means `tc_printf` is not called during
the `_flash_range_erase`. This is important as `_flash_range_erase` is
used when loading. This fixes the issue:
https://github.com/blacksphere/blackmagic/issues/875
Also adding spinner timeout counter to reduce bus traffic.
2021-05-16 11:26:14 +02:00
67c9003522
rp: Flush cache after erase and write
...
The RP2040 datasheet suggests that _flash_flush_cache and _flash_enter_cmd_xip
should be called after erasing and writing to flash.
2021-05-16 11:26:14 +02:00
f880734050
Fix compiling for native probe
2021-05-16 11:26:14 +02:00
e4421799ba
More header cleanup
2021-05-15 12:54:51 +02:00
8e438b9e5f
Add missing headers and remove double typedef.
2021-05-14 19:58:16 +02:00
cfbe9f1c94
pc/gdb_if.c: More verbosity for Error messages #873
...
Thanks to "pshri" for dissecting and adding messages, as problems with
Hpyer-V and port permissions happened on Win10
2021-05-09 11:49:32 +02:00
f121350fc9
hosted/cmsis_dap: Verify that a v2 interface has endpoints.
2021-04-27 11:39:43 +02:00
494524dd85
hosted/cmsis_dap: Add v2 support.
2021-04-27 10:26:06 +02:00
4f52a7b235
hosted/cmsis_dap: Add discovery by interface string and prepare for v2 support.
2021-04-26 21:56:24 +02:00
c4874fdf44
hosted/dap: Add parentheses around bitwise operator.
2021-04-26 21:54:38 +02:00
f9414d5826
cmsis-dap: Handle ADI DP22 devices on probes not multidrop capable.
2021-04-26 18:18:18 +02:00
923edc7f7e
cmsis-dap: Fix wrong handling when reading data not word-aligned
2021-04-26 15:08:09 +02:00
877a6e694c
Revert "cmsis_dap: Always write full reportsize + 1 buffers"
...
This reverts commit 61e237ec87
2021-04-25 22:53:40 +02:00
1f67bab475
nxpke04: Move unsafe_enables to target bool union.
2021-04-25 16:03:23 +02:00
f87dff8d83
kinetis: Remove static variables, add word union to target_s.
...
Add a word union to target structure to hold a single word variable.
2021-04-25 16:03:23 +02:00
ac7c1057cc
efm32/samd/samx5x: Remove static allocates strings. Allocate in priv_storage.
...
Static allocated variables in the different targets eat up common RAM and
will collide in chains with multiple similar targets.
2021-04-25 16:03:23 +02:00
cddf02f174
samx5: Verbose error reports on protected devices.
2021-04-25 16:03:23 +02:00
8c8aa980cf
adiv5: Detect unprotected SAMD5x only once
2021-04-25 16:02:20 +02:00
f98b7274b4
hosted/stlinkv3: Detect STlinkV3 in bootloader mode.
2021-04-25 16:02:20 +02:00
a83700d1cf
stm32/usbuart: DMA stream handling is not STM32F4 specific
2021-04-25 16:02:20 +02:00
1330288271
firmware: Unify serial number handling
...
Use one file in dfu and server
For STM32, provide 3 ways to handle
- BMP way (8 bytes)
- DFU way (12 Bytes)
- Full unique id (24 Bytes), as with STLINK(V3) Bootloader
2021-04-25 16:02:20 +02:00
1b26ff560d
rp.c: Add reset_usb_boot as monitor command
2021-04-24 14:48:58 +02:00
52bffa70cf
rp: Handle flash.
...
- Beware, after reset, only a valid flash payload get mapped to XIP!
Only 0 is read from flash when flash image is not valid
2021-04-21 21:55:03 +02:00
2b0e255c40
cortexm: timeout and debug for run_stub()
2021-04-21 21:50:38 +02:00
61efe26348
swdp_scan: Break infinite loop after Dormant->SWD transition.
2021-04-21 21:50:38 +02:00
fa5e69e3be
RP 2040: Special handling for rescue DP
...
As the rescue DP provided no AP, trigger the reset with attach().
However attach will indicate failure also reset/halt has succeeded.
2021-04-21 21:50:38 +02:00
ea92c8b8c8
cmsis-dap: Allow to use adiv5_swdp_scan.
2021-04-21 21:50:38 +02:00
23f942ac8c
Raspberry RP2040: Recognize. No flash handling yet.
2021-04-21 21:50:35 +02:00
04d1c9805b
swd: Remove swd_proc and swdptap.h.
2021-04-21 21:50:04 +02:00
b6fbf86743
Extend ADIv5_DP_t for low level routines needed for multi-drop.
...
Will replace swd_proc
2021-04-21 21:50:04 +02:00
61e237ec87
cmsis_dap: Always write full reportsize + 1 buffers
...
Expect short reads and other errors else
2021-04-21 21:50:04 +02:00
d6ade4d94e
cmsis-dap: Use SWD_SEQUENCE if available.
2021-04-21 21:50:04 +02:00
5abb288c7a
hosted: Provide the DP functions in swd_proc.
2021-04-21 21:50:04 +02:00
fa561c8d66
adiv5_swdp: Starting point to handle multi-drop
...
- RP2040 show both DPs
- Multidrop test with STM32L552 and STM32H745 allows selection
with "-m 0x4500041" (H7), "-m 1" (L552) or "-m 0x01002927" (RP2040)
2021-04-21 21:50:04 +02:00
be3bfc48a8
cortexm: M33 has up to 8 hardware breakpoints
2021-04-21 21:22:59 +02:00
b1ac4187b9
Fix some formatting strings for 32-bit compile
2021-04-21 21:22:59 +02:00
637d76b585
cl_utils.c: Try jtag scan if swd scan did not give results.
2021-04-21 21:22:59 +02:00
5288eef617
cl_utils: With no size given, read the size of the lowest block.
2021-04-20 18:48:27 +02:00
beaccf2714
target: stm32l4: add support for STM32WLxx
...
This adds support for the STM32WL series in stm32l4.c. These parts have
the same flash registers layout as the L4 series, but a different base.
Since there are already two sets of registers in this target file, this
adds support for register maps that can be customized for each device
ID.
2021-04-20 18:42:36 +02:00
21b80949ff
Compile with -Os as default. Change like "make OPT_FLAGS=..."
...
SWD/JTAG Bitbang is compiled with -O3 for good bitbang speed.
2021-04-20 18:20:41 +02:00
f55ad67b1b
adiv5: catch timeout on adiv5_ap_read_id and abort
...
This adds a TRY_CATCH around the adiv5_ap_read_id() in
adiv5_component_probe() and resets the DP when that happens.
It seems like the STM32WLE5 comes with the AP of the inactive core
enabled in a way that does not make it detectable, and the current code
times out and leaves the whole device hanging.
Catching the timeout and calling adiv5_dp_abort() seems to restore the
device to a useable state.
Tested on Seed LoRa-E5 (STM32E5JC).
2021-04-19 16:57:13 +02:00
806787529f
Use DMA for USBUSART TX/RX
2021-04-17 17:57:08 +02:00
cf5b4afb38
bmp_serial/linux: Honor opt_list_only (-l).
2021-04-17 16:19:57 +02:00
d6b24c00c8
Fixed STM32G43x/G44x option bytes support
...
Previously took L4 values so FLASH_SEC1R was not applied
2021-04-17 14:44:30 +02:00
99f9557cc0
Support for STM32G49x/G4Ax (category 4)
2021-04-17 14:44:30 +02:00
c85c946ce3
PRIx32 fix
2021-04-17 14:44:30 +02:00
9ec7d05d8d
Put null terminating characters when scanning for BMP probes on linux
...
This patch puts null terminating characters for the 'type',
'version', and 'serial' strings extracted from blackmagic probe
id strings on linux systems.
2021-04-17 14:41:28 +02:00
299da8627c
libftdi: Remove unneeded explicit path.
2021-04-17 13:35:21 +02:00
a6a8606edb
STM32L55: Detect, memory map, read and flash write. Options handling missing.
...
Only non-secure states considered!
2021-04-04 17:26:31 +02:00
739941dc5f
Verify right after programming
2021-03-31 13:06:52 +02:00
2982888b66
BMP_MODE_FLASH_WRITE_VERIFY combined operation
2021-03-31 12:07:53 +02:00
f85c54be97
Prepared -w option
2021-03-31 12:07:53 +02:00
6d6cfd6c98
Comprehensive STM32G03/4/5/6/7/8/B/C driver
2021-03-29 21:42:40 +02:00
58f153e12b
cortexm: Always halt and release reset before romtable scan
...
Only release from halt once after romtable scan
Should fix #836 .
2021-03-26 17:43:11 +01:00
a025c9a7bd
Revert "stm32f1: On ST parts there is no need to read IDCODE again."
...
Romtable partno is not unique for devices, e.g. in STM32F0
This reverts commit f89b07d892
2021-03-26 17:35:00 +01:00
f89b07d892
stm32f1: On ST parts there is no need to read IDCODE again.
...
IDCODE is already known from the Romtable
Probably this has the same effect as #836
2021-03-12 20:45:34 +01:00
e6a9a1a366
cmsis-dap: Get the firmware version.
2021-03-06 13:30:09 +01:00
7859a2aabd
adiv5_swd: Factor out creation of packet request.
2021-03-06 13:30:09 +01:00
cfb784d428
adiv5: Fix comments and debug output
2021-03-05 16:49:19 +01:00
3aa6f16964
serial_unix: Split timeout in seconds and microseconds
...
Macos exposed errors when tv_usec was > 1000000.
2021-03-05 16:49:19 +01:00
43770736f1
cl_utils: Rework Flash/Ram printout
2021-03-05 16:49:19 +01:00
560a046a22
Add support for NXP LPC802, LPC804, LPC832 and LPC834
2021-02-22 19:37:46 +01:00
0df44e205b
ADIv5: Abort Romtable scan also if CIDR0 is invalid after halting #832
...
STM32WLE5 has the same dual core chip as STM32WL5. For the second
core, the additional AP can be see, but access to e.g. CIDR0 for that
Romtable fails.
Aborting the scan too if again the second read of CIDR0 fails makes
sense anyways!
2021-02-19 18:48:02 +01:00
d70fa8c7f6
hosted: Remove restrictions when gathering information on the debugger
...
That way, we find RPI Pico pico-debug.
2021-02-15 17:47:29 +01:00
c776e7a9a6
swd_scan: Add '-m' as targetid argument to swd_scan to prepare multi-drop.
...
In a real multi-drop setup, the device to use must be specified.
2021-02-15 17:47:29 +01:00
8e2f6937d5
hosted: Run target specific monitor commands with -M "command" .
...
Lists available commands: "blackmagic -M help"
Quote multi argument monitor commands, e.g. STM32F1: blackmagic -M "option help"
2021-02-15 17:47:29 +01:00
165560edd8
cl_utils: target selection '-n' argument needs optarg.
...
foreach now returns the number of targets.
2021-02-15 17:47:29 +01:00
4eb336277c
native: Remove high current draw ( #814 )
...
Special iRST_SENSE handling does not apply at least for BMP 2.1c.
On V2.1c, iRST_SENSE was set as output high and xRST high shorted
iRST_SENSE to ground via Q2
FIXME: Check for older versions!
2021-02-15 15:00:19 +01:00
3b8502c2e5
add space in USB product string (be consistent with ../stm32/dfucore.c)
...
This changes the USB identification from
"Black Magic Probe(STLINK/V2) v..." to
"Black Magic Probe (STLINK/V2) v..."
Signed-off-by: Martin <Ho-Ro@users.noreply.github.com>
2021-01-29 14:47:28 +01:00
d4dc3b2717
The USB CDC is no modem and does not use the AT protocol
...
Signed-off-by: Martin <Ho-Ro@users.noreply.github.com>
2021-01-29 14:47:28 +01:00
42f590ce0b
fixing some memory map errors for stm32h7, PR #821
2020-12-23 20:10:39 +01:00
09c000eca8
hosted: Really handle setting tpwr on remote on the command line #817
...
Expect the command to fail, due to old firmware or remote not implementing
the power switch.
2020-12-19 16:36:09 +01:00
2b06f045c4
target: kinetis: add S32K148
...
This adds support for the NXP S32K148. This is an automotive-grade part
that is derived from the Kinetis line, so it has a very similar
interface to other parts in the family.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-12-16 12:49:23 +01:00
5f76169b95
hosted: remove ftdi include when built with BMP_ONLY #811
...
Signed-off-by: Sean Cross <sean@xobs.io>
2020-12-16 11:30:42 +01:00
98c92a6d18
hosted: Really fix the case of no serial number ( #807 )
2020-12-13 14:12:05 +01:00
aa0d8f4b5d
Merge pull request #783 from UweBonnes/frequency
...
Frequency
2020-12-12 19:50:53 +01:00
020600aa56
target/lpc546xx: fix lpc546xx flash support ( #801 )
...
**Summary**
Modifications to fix flash support on the lpc546xx:
- fix IAP entrypoint to be `0x03000204`, not the value at that address
- add a reset and attach sequence before erasing flash sectors. there's
little documentation around this, but experimentally, erasing sector 0
fails when the ROM bootloader is mapped to it (on reset). stepping the
chip once and attaching is enough to snap the chip out of it, permitting
flash erase on sector 0.
- add a few test commands to the lpc546xx table (read_uid, erase/write
sector, etc).
- write the magic CRC value when writing to sector 0
(`lpc_flash_write_magic_vect`).
- move the lpc546xx probe to before the lpc43xx probe, to prevent
getting the lpc546xx into Lockup when reading an illegal memory location
during lpc43xx probing
Fixes #786 .
I don't 100% understand the reset/load sequence of this part, but these
changes are sufficient to program and debug the part now.
I didn't do a detailed analysis of what pyocd (via st-link hardware
adapter) and segger jlink do to handle the same, but both of those
worked without modification, so there's some difference in the
sequence they're using.
**Testing**
Verified I can now successfully erase and write an executable in sector
0 (and other sectors).
Verified the new commands work correctly.
2020-12-12 19:48:05 +01:00
6dbb5ff7ee
Frequency: Implementing for jlink.
...
SWD frequency is fixed for jlink according to the docs from 2010.
2020-12-12 18:33:09 +01:00
fdc654cfb3
stlink: Implementation of frequency setting.
2020-12-12 18:33:09 +01:00
de26ba6f73
hosted: Add is_jtag to the info structure
...
Needed for different frequency setting procedures on some platforms.
2020-12-12 18:33:09 +01:00
28a966a3e6
frequency: Implement for ftdi.
...
For all 2232H types, use undivided 60 Mhz.
FIXME: Check FT2322C/D for unsymetric clock at 6 MHz!
2020-12-12 18:33:09 +01:00
13e8a262e4
SWJ Frequency: Implement for cmsis-dap
2020-12-12 18:33:09 +01:00
1ca9f234f7
Infrastructure for setting maximum SWJ frequency.
...
Implement for BMP/firmware on STM32.
2020-12-12 18:33:09 +01:00
7365a44989
hosted: Implement SWJ test mode (-T).
...
Continious read/write-back some core register as NOP operation to allow scope
measurement of SWJ timing.
2020-12-12 18:33:09 +01:00
f796b774bd
hosted: Fix info.serial if USB device has no serial number #807
2020-12-12 18:32:15 +01:00
518529a772
Support GD32E23x
2020-12-12 18:29:30 +01:00
14498decd9
HOSTED_BMP_ONLY/linux: Fix case when no serial device is connected #806
2020-12-12 15:06:26 +01:00
93d4c65948
Fix building with newer GNU make( #804 )
...
More recent versions of GNU make remove the `-` prefix from
`$(MAKEFLAGS)`, which breaks the build:
```bash
# output truncated to interesting parts
> make -C src --trace all_platforms
set -e ;\
mkdir -p artifacts/v1.7.1-91-g98b4ec5 ;\
echo "<html><body><ul>" > artifacts/index.html ;\
for i in platforms/*/Makefile.inc ; do \
...\
make w --trace --no-print-directory clean ;\
make w --trace --no-print-directory;\
...\
done ;\
echo "</ul></body></html>" >> artifacts/index.html ;\
cp artifacts/*.bin artifacts/v1.7.1-91-g98b4ec5
Building for hardware platform: f4discovery
make[1]: *** No rule to make target 'w'. Stop.
```
Per the
[documentation](https://www.gnu.org/software/make/manual/html_node/Options_002fRecursion.html ),
there's no need to manually apply insert `$(MAKEFLAGS)`, it should be
automatically included when using `$(MAKE)` when recursing.
I tested on my machine (make 4.2.1) and a docker image based on
ubuntu:trusty (make 3.81), both behaved the same (directories were not
printed when recursing by default);
2020-12-12 14:39:52 +01:00
b5172cf6df
Implement the 'find_debuggers()' function for hosted BMP on windows.
2020-12-11 18:36:48 +01:00
01f8628aed
Bugfix in detecting BMP probes by usb serial number.
2020-12-11 18:36:48 +01:00
170fe0c368
Remove spurious comment.
2020-12-11 18:36:16 +01:00
4c5ce0b16a
Hosted: Handle devices w/o serial number, e.g. GigaDevices GD-Link ARM/CMSIS-DAP
2020-12-11 18:36:16 +01:00
0f1fe9e438
hosted/linux: Find BMP devices without libusb.
2020-12-11 18:36:09 +01:00
bd5f4c6ed5
hosted: Consolidate ident output.
2020-12-11 17:55:31 +01:00
0870b778c0
hosted: Allow to build without libusb, libftdi and hidapi with HOSTED_BMP_ONLY=1
2020-12-11 17:50:16 +01:00
32db38ecf2
hosted/libusb: Move platform.c libusb related functions to own file.
2020-12-11 17:35:43 +01:00
41788f923b
ftdi/stlink/jlink: Provide dummy functions in the HOSTED_BMP_ONLY case
...
Do not allow multiple inclusion by not declaring the functions as static to
help keep code clean.
2020-12-11 17:31:25 +01:00
98b4ec58bc
Update to recent libopencm3 to undo unwanted change.
2020-12-07 21:51:22 +01:00
633c6a2e81
Recognize "J-Trace Cortex-M PRO V2" in hosted mode
2020-12-07 11:52:33 +01:00
17dfec3572
dfu/cdcacm: Consolidate usage of ST vs BMP serial number.
2020-12-06 15:18:08 +01:00
5c7e0eedb0
command.c: Consolidate "mon version" output
2020-12-06 15:18:08 +01:00
07c3699225
version.h: Remove from platform.h files
...
- Consolidate ident string generation
- Recompile only needed files
2020-12-06 15:18:08 +01:00
dd6aadc54d
jtag: Add verbosity about devices found.
2020-12-06 15:18:08 +01:00
0a7bfd5923
dfu_f4: Fix sector_erase.
2020-12-06 15:18:08 +01:00
e318f884bf
Change the type of 'cortexm_wait_timeout' to unsigned.
...
It makes sense that the timeout value is unsigned, it also
resolves build errors on some platforms.
2020-12-04 11:44:50 +01:00
c9a419e44b
Correct loss of sync protocol error #787
2020-12-04 11:33:23 +01:00
e3fd12ebc6
gd32f1/f3 detection and ram/flash autoset
2020-12-03 11:16:47 +01:00
575c25e570
Add support for STM32F1 clone with new AP_DESIGNER id
2020-12-01 10:23:16 +01:00
48a79ff9da
adiv5: More checks for a sensible DPIDR.
2020-11-29 21:11:11 +01:00
752bc26536
adiv5: Fix memleak with duplicated base.
2020-11-29 21:11:11 +01:00
acec489647
adiv5_jtagdp: Always set idcode.
2020-11-29 21:11:11 +01:00
9e1b7fdac0
jlink/swd_low_access: Fix data direction during response read phase.
2020-11-29 15:48:50 +01:00
8903026c14
jlink/swd: swd frequency is fixed, not need to set.
2020-11-29 15:48:50 +01:00
f45c56af83
adiv5/swdp: Check early for valid DP idcode.
2020-11-29 15:48:50 +01:00
3b6432912d
jlink: Catch another error with no target connected.
2020-11-29 15:48:50 +01:00
7df314e265
Firmware/Jlink: Fix double free when debug power-up fails ( #780 )
2020-11-29 15:48:50 +01:00
e1329499de
platform_adiv5_swdp_scan: Do not double free with early errors.
...
adiv5_dp_init() clean up itself if errors happen
2020-11-29 15:48:50 +01:00
bf548e92c0
swd: After write low_access, always append 8 clk to move data through SW-DP.
...
Especially needed when leaving the debugger or during debug unit power-up.
ARM Debug Interface Architecture Specification ADIv5.0 to ADIv5.2
tells to clock the data through SW-DP to either :
- immediate start a new transaction
- continue to drive idle cycles
- or clock at least 8 idle cycles
Implement last option to favour correctness over slight speed decrease
Implement only for adapters where we assemble the seq_out_parity in our code,
as on firmware, ftdi and jlink. Hopefully the high level adapters do it right.
Reverts 2c33cde63fcde7726b87
2020-11-27 22:26:48 +01:00
139e5d7e22
f4discovery: Compile time option to compile with ST bootloader
...
Just to keep things active. Prepare for F72 bootloader.
2020-11-27 22:26:48 +01:00
636bcee355
stlink/swlink: Remove the DFU upgrade utility.
...
Hopefully no old bootloaders are around. If otherwise, revert to last
commit before this and update the DFU bootloader.
2020-11-27 22:26:48 +01:00
27ef4569ca
stm32/dfucore.c: Use libopencm3 provided defines and functions.
2020-11-27 22:26:48 +01:00
9d55128ab8
cl_utils: Get voltage only once.
2020-11-27 22:26:48 +01:00
e6823f39de
Hosted: Print version with "-h" and "-t" option.
2020-11-27 22:26:48 +01:00
3ee31473c6
cortexm.c: LPC15xx has designer 43b and Partno 4c3
...
Thanks to JojoS!
2020-11-27 22:26:48 +01:00
62d9f60f03
hosted/firmware: Waits for read response as long as cortexm_wait_timeout.
2020-11-27 22:26:48 +01:00
26a23dd1cb
stlinkv2: Try harder to open an AP.
...
Problem seen on STM32L0 with probably long sleep periods.
2020-11-27 22:26:48 +01:00
19e1fddba2
adiv5: Remove unnescessary read.
2020-11-27 22:26:48 +01:00
cda83d3084
Fix memleaks.
...
Happened e.g. when Stlink could not enter debug or when cortexm_prepare timed out.
2020-11-27 22:26:48 +01:00
9ac5adfcef
adiv5: Additional decoding.
2020-11-27 22:26:48 +01:00
d78d7838d3
stm32f1: Always read DBGMCU_IDCODE for t->idcode ( #770 )
...
At least STM32F042 has 0x440 as romtable partno vs 0x445 as DBGMCU_IDCODE.
Thanks to Andrey Melnikov(aam335) for pointing out!
2020-11-27 22:26:48 +01:00
653d486ee2
cortexm: Store CPUID in target structure.
2020-11-27 22:26:48 +01:00
824a1d8abc
hosted/find_debuggers: Do not check hubs. Print class of devices unable to open.
2020-11-27 22:26:48 +01:00
e68dd25813
cl_utils: Clarify -d option is BMP/firmware only and deprecate -d.
2020-11-27 22:26:48 +01:00
f71e18948a
GPIO for SWD: Slow down edges on more platforms.
2020-11-27 22:26:48 +01:00
80154c5c7a
adiv5_swdp: Fix more memory leak.
2020-11-27 22:26:48 +01:00
35bcb4f7c6
Switch on the lpc546xx target
...
Enable the lpc546xx target. Tested on the LPCXpresso54628 dev board,
able to flash and debug.
2020-11-24 21:32:39 +01:00
e9c02296f2
target: kinetis: add S32K118
...
This adds support for the NXP S32K118. This is an automotive-grade part
that is derived from the Kinetis line, so it has a very similar
interface to other parts in the family.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-11-14 13:06:23 +01:00
f18be6ef7a
Add support for Kinetis K12 and placeholders for other K-series MCUs
2020-11-07 12:44:05 +01:00
2c33cde63f
cortexm.c/cortexm_halt_resume: Add some clock cycles to always get CPU going ( #768 )
2020-11-01 21:53:23 +01:00
d75f3124b9
ftdi_bmp.c: Reapply fix from #715 : Check for libftdi 1.5
2020-11-01 12:09:27 +01:00
99142d1c0e
Add documentation details for building PC-hosted BMP in msys2.
2020-11-01 11:33:54 +01:00
1f7a716710
adiv5.c: Run cortexm_prepare on all suspected CortexM instances.
...
Gets all debug units of the second CPU of a STM32H745 visible.
2020-10-23 09:40:15 +02:00
18673d9a56
adiv5: Rework DP/AP refcounting.
...
ASAN non longer reports leaks with the STM32H745.
2020-10-23 09:40:15 +02:00
f76a7c4e92
adiv5: Release devices after scan.
...
Before, scanning only kept device stopped until POR or attach/detach cycle.
2020-10-23 09:40:15 +02:00
73e6b540b2
command: When debug channel is available, print morse messages readable.
2020-10-23 09:40:15 +02:00
776861c6a0
Makefile: Fix version.h generation for make all_platforms
...
Same fix as 0ae65cc10f
2020-10-23 09:40:15 +02:00
80ddafc2f8
Jtag/High Level : Transfer dp->dp_jd_index with every HL command.
...
- Add REMOTE_HL_VERSION, now at 1. Fall back to hosted/low-level
when wrong version is found and give hint to user.
2020-10-23 09:40:15 +02:00
59dc1b7eb4
cortex-m7: Give hint about buggy core revision.
2020-10-23 09:40:15 +02:00
976c763747
jtag remote: Start fixing handling M0 (second jtag) for LPC4322 in high-level
...
- LPC11: Only print none-null unknown idcodes.
2020-10-23 09:40:15 +02:00
0995fe1288
cmsis-dap: Various fixes
...
- decrease report size to 64, otherwise MIMRXT10x0-EVK crashed when
reading larger memory block
- dp_read_reg acts direct, fixing CortexM core register read.
- length of data to write with read_block.
2020-10-23 09:40:15 +02:00
Uwe Bonnes
SG
fabalthazar
Vegard Storheil Eriksen
Jeff Lutgen
Thiadmer Riemersma
Andy Makovec
dpc
Thiadmer Riemersma
aam335
Björn Mellström
James Turton
Fabio Baltieri
Vestrel
Stoyan Shopov
Martin
Alex Norman
Sean Cross
Noah Pendleton
Aaron Lindsay
Noah Pendleton
Emilio Lopes
mean
Jonathan Giles
jbuonagurio