We don't actually allow the user to change this at present, so one
could argue that we should remove it from what is saved out of the
config. But this is a smaller, safer change.
Fixes https://gitlab.com/kicad/code/kicad/issues/7666
1) Don't report on tests not run.
2) Don't cancel subsequent tests because the current test didn't
have any constraints
3) Exit a little bit quicker when cancelled
Fixes https://gitlab.com/kicad/code/kicad/issues/7724
Push DRC zone RTrees into BOARD so that they can also be used by
insideArea.
All these caches are a bit of an encapsulation leak, but they make a
significant impact on performance.
Fixes https://gitlab.com/kicad/code/kicad/issues/7720
The reference designator is stored separately with the Tracks, so we
need to extract position/size data from it there and match back to the
components later.
Fixes https://gitlab.com/kicad/code/kicad/issues/7733
Find all intersecting points both forward and back between the filled
areas and the outlines in order to determine the proper net assignment
for the zones
Also creates rule areas for special zones instead of filled zones
Fixes https://gitlab.com/kicad/code/kicad/issues/7732
Old boards were using UNDEFINED_DRILL_DIAMETER value in file for via drill when
the via drill value was the netclass value.
Recent boards always set the via drill to the actual value, but now we need
to be sure always store the drill value, because netclass value is not stored
in the board file. Otherwise the drill value of some (old) vias can be unknown
The rotate mirror actions need to line up with the expectation.
FABMASTER keeps elements board-referenced while KiCad has some elements
referenced to the board and some referenced to the footprint
wxWidgets' UTF8 mode wasn't thread-safe, so we had to put mutex's on
a bunch of string operations, which meant that we couldn't return
references to strings. Now that we no longer use UTF8 mode anywhere
(and the mutex's were removed long ago), using references is a big
performance win in some places.
Between the time the user loads the footprint preview in cvpcb or Add
Footprint in pcbnew, we don't need to verify cache integrity to display
the footprint. We use the cache copy when displaying until we close the
selection window and re-open. This limits our need to iterate over the
full directory on every footprint display.
Alternate solutions for v7 should include looking into libfswatch for
change detection
Timestamps were checked using a different routine than they were
generated with, leading to the cache always being out of date.
This uses the same routine for both. While it iterates over the
directory twice during the initial load, this will never be dominant
Fixes https://gitlab.com/kicad/code/kicad/issues/7711
The move tool can stack on others, so when we re-enter the previous tool
this caused another immediate action. We flag re-entry in the tool
stack to check for this and avoid unexpected tool starts
When a user clicks on the "Add Component", "Add Power" or "Add Footprint"
icon, they want to add the item. Requiring an extra click on the screen
before selecting the component/footprint is not needed.
We auto-size them in the code and doing both produces nothing but a
mess.
Also improves the auto-sizing for the layers drop-down (particularly
needed for the new, somewhat longer, layer names.
Fixes https://gitlab.com/kicad/code/kicad/issues/7671
Also remove an implicit zone merge that was happening when the user
edited the zone parameters. This appears to have been a feature but it
happened without a) telling the user and b) having the option to prevent
it.
Fixes https://gitlab.com/kicad/code/kicad/issues/7661
We cannot do forward/reverse annotation in Single Top mode because we
depend on shared memory access. This disables the menu options in this
case and replaces the toolbar update pcb icon with the import netlist,
which is more appropriate for single top mode
Fixes https://gitlab.com/kicad/code/kicad/issues/7637
- Rename member variable names to use the 'm_' prefix
- Rename a few object types that clashed with KiCad object names, such
as BOARD and SCHEMATIC, to avoid the use of '::' to access the KiCad
objects.
- Remove some unused code.
Add a reset button that will only show up if the user
edits the JSON configuration for grids. This is a temporary
measure until we have a real grid editor GUI in V7.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7595
Each symbol unit in eeschema has a unique identifier. But we don't have
a unique identifier for the entire symbol. So changing which symbol
instance was unit A (our default base for matching), changed the UUID
that we were using to match the footprints.
This commit adds all UUIDs to the netlist, allowing us to match symbol
to footprint without worrying about which unit is referenced.
This still does not handle changing different units on different sheets.
Fixes https://gitlab.com/kicad/code/kicad/issues/7604
First issue: the C++ action plugins list should be cleared so that any
plugins that fail to reload do not hang around on the toolbar.
This is fixed on the C++ side.
Second issue: inner dependencies of plugins that are modules were not
reloaded before, which broke reloading for many plugin examples out there.
This is fixed on the Python side by keeping track of dependencies and
clearing them out before reloading a module (unfortunately there doesn't
seem to be a way to do this in the standard library)
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7245
This change is mainly due to the fact Modal dialogs do not work when our
current tool is the tool used to create new item (text, zone, graphic).
If when this tool is active, one try to edit the properties of the new item
being created (or being placed) the modal dialog does not capture the event tool
and hangs (cannot be dismissed)
Our quasi modal dialogs have their own event loop and work.
Fixes#7585https://gitlab.com/kicad/code/kicad/issues/7585
CHANGED: If the user made a selection and then tried dragging it, the
drag would only succeed if the selection contained at least one
footprint. Selections with only tracks and vias would instead make
KiCad drag a new selection box.
This MR allows routing of selections of a single track or via, while moving
selections containing more than one item, whether or not they also contain
a footprint.
Fixes https://gitlab.com/kicad/code/kicad/issues/7539
- Make DIALOG_SHIM::SetPosition working)
- rename PCB_BASE_FRAME::SelectLayer() to PCB_BASE_FRAME::SelectOneLayer()
- PCB_BASE_FRAME::SelectOneLayer(): make dismiss dialog by escape key working.
Fixes#7578https://gitlab.com/kicad/code/kicad/issues/7578
Assume that the user has locked tracks/vias for a reason and would very
much like them to remain in place, regardless of the operation
Fixes https://gitlab.com/kicad/code/kicad/issues/7562
1) Don't remove items from group when the group is being deleted as
well. We need those pointers for undo/redo.
2) Flip the GROUP/UNGROUP undo status when undoing/redoing group and
ungroup actions.
3) Remove PCB_GROUP_T from the rebuild-netlists section. Nothing
about an item's group/ungrouped status changes its netlisting.
4) Add PCB_PAD_T to the rebuild-netlists section. It can probably
only happen in the footprint editor where we don't care about
netlisting, but it's conceptually more correct and who knows what
might change in the future....
Fixes https://gitlab.com/kicad/code/kicad/issues/7540
This simple commit makes the Pcbnew copy to clipboard operation snap the
obtained cursor position to grid before the anchors are calculated. This
is also the way the move operation has been apparently working so far.
To be clear, this will not remove all cases where the copy reference
point is not aligned to the grid (see the linked Gitlab issue for
details about the problem). This will still occur for zone outlines that
are not axis-aligned. But such behavior has been so far also present in
the moving operation, so this may be as designed.
Fixes https://gitlab.com/kicad/code/kicad/issues/7507
For some kinds of issues, we want a way to point them out but
we don't need to keep the user from being able to close the
dialog. A separate Validate button lets the user check for
issues if desired, but these issues are not "fatal" and can
be ignored if the user wishes.
The removal of the pcbnew general section was meant for v6 but passed
the deadline. This removes the duplication of thickness. We do not
allow the thickness to be different between nominal and stackup, so
keeping separate text fields is unnecesarily confusing to users
The automatic wire tool was not working in the gridless mode because the
grid snapping on/off logic present in `EE_GRID_HELPER`, based on the
value of `m_enableGrid`, was not taking into account that another check,
but for the global KiCad setting, would be performed in the `Align()`
method, which is inherited from `GRID_HELPER`.
I've modified all tests of `m_enableGrid` value to also take the global
setting into account, and moved checks for it to `Align()` method, as
it's more consistent this way.
I've also removed an override of the `Align()` method in the
`PCB_GRID_HELPER` class, as it was made redundant by my changes.
Fixes https://gitlab.com/kicad/code/kicad/issues/7402
Some CADSTAR designs use zero sized pads because CADSTAR did not allow
arbitrarily assigning pad numbers: they had to be sequential. The
workaround to this was to use zero sized pads. However this causes DRC
errors in KiCad, so we load them just in a mask layer.
1. Make sure to convert to KiCad units
2. There are some KiCad rules that have no CADSTAR equivalent.
Make a guess as to what an appropriate rule could be.
It just means the outline wasn't malformed. It might still be
empty.
[Edit: my fix collided with JP's, so all this really is now is a
couple of slight performance improvements.]
Keep Through Hole pads on external layers should be ON by default, because
such a pad does not allow soldering/unsoldering, if this option this option is OFF
Also rename dialog_enum_pads.fbp as dialog_enum_pads_base.fbp, as usual
Keeps parent information such as UUID and pad removal options for
elements that are just updated in routing rather than created fresh or
fully destroyed.
Fixes https://gitlab.com/kicad/code/kicad/issues/7460
You had to set the line width in the SVG export dialog in order to
change the displayed line width in the 3d viewer. The line width did
not affect the SVG export. Removing in favor of the Board design
settings for line widths
Some differences are due to difference between libraries being files
in symbol editor and directories in footprint editor, but this unifies
most of the rest.
It also dispenses with the save-to-library vs save-to-document distinction
in the GUI because it makes for too much variability in the GUI, was
implemented differently between the two editors, and isn't needed as much
anymore now that we have the highly visible infobar.
There was also an issue that the save-to-board icon occupies the same
location and has the same size/shape/colours as the Board Setup icon in
PCBNew.
Fixes https://gitlab.com/kicad/code/kicad/issues/7215
Physical layer test needs to be board-visible-layers, not pad-layers.
Also cleans up the tests so that LOD factors in. (When things
disappear due to zoom level they should not be selectable.)
Fixes https://gitlab.com/kicad/code/kicad/issues/7238
Now that footprint properties inherit custom fields from schematic
they are very useful.
Setting custom properties from python will also be handy in plugins
that need to somehow mark their own objects.
Stores a cache of the convex hull similar to the bounding box. Modifies
the hull based on actions to allow complex footprint graphics without delay
Fixes https://gitlab.com/kicad/code/kicad/issues/7341
This no longer returns the first pad, just the first by pad sort order
in output. The call is not used correctly in pcbnew, so removing to
prevent future misuse
For some reason the post-pinned local variable references were replaced
with calls to the points themselves (which are the pre-pinned values).
Fixes https://gitlab.com/kicad/code/kicad/issues/7291
The nettie hack is used in DRC but we also need to use it in zone filler
to allow zones to be used with netties. We limit this to the
appropriate nets in the nettie
Fixes https://gitlab.com/kicad/code/kicad/issues/7351
The conditions prevent use in immediate mode for common actions. While
this makes enable/disable easier in menu items, this fix is a patch
until we refactor the action framework to distinguish between immediate
mode hotkeys that should start without selections and menu items that
need a selection before running.
Fixes https://gitlab.com/kicad/code/kicad/issues/5333
One way to do this would have been to keep the Uuids in the editor
copy. However, this opens us up to errors if we forget a Save As or
export path and end up writing the Uuids out somewhere else.
In the end, it felt safer to store a map of the original Uuids and
restore them if we happen to save the editor footprint back to the
board.
Fixes https://gitlab.com/kicad/code/kicad/issues/7312
... because that's where we do hole-to-copper clearance testing.
Also augments the Clearance Resolution reporter to report on said
hole clearances.
And changes the interpretation of HOLE_CLEARANCE_CONSTRAINT to include
local pad clearance overrides.
Fixes https://gitlab.com/kicad/code/kicad/issues/7325
New strategy isolates all draw/don't draw decisions to the ViewGetLOD
routines, and all dimmed/not dimmed to PCB_RENDER_SETTINGS::GetColor.
The actual drawing in PCB_PAINTER is more-or-less conditon free.
Also adds new layers for pad and via hole walls so that they can be
controlled for high-contrast mode.
Also changes the drawing paradigm so that the pads are drawn even when
not on the high contrast layer, just in low contrast. The hole wall
is drawn in high contrast. This actually makes things clearer to the
user (although to be honest was done to keep from having to re-render
pads when the high contrast layer changes since we have two separate
layers now that we can adjut colours on).
Fixes https://gitlab.com/kicad/code/kicad/issues/7328
Moves rule area triangulation outside of layer iterator and keeps the
triangulation_valid flag false until the triangulation has been
completed.
Fixes https://gitlab.com/kicad/code/kicad/issues/7032
Non-layer elements can be logical centers for the circle and arc tools.
We allow the non-layer to snap for the center points and revert to only
on-layer elements after
Fixes https://gitlab.com/kicad/code/kicad/issues/7327
Marek Roszko
Jon Evans
Mikolaj Wielgus
Jeff Young
Ian McInerney
WhiteChairFromIkea
Jonathan Haas
qu1ck
Wayne Stambaugh
Seth Hillbrand
jean-pierre charras
Tomasz Wlostowski
david-beinder
Roberto Fernandez Bautista
Zoltan Gyarmati
PJM
James Jackson
Simon Richter
Thomas Pointhuber
Michael Kavanagh