Highlight connections is meant to show the copper connections on a
board. We remove the non-copper pads from our selection when attempting
to source the net for highlighting.
Fixes: lp:1815898
* https://bugs.launchpad.net/kicad/+bug/1815898
Choosing the drag origin should not be dependent on the snap settings in
pcbnew. Snap settings are sensible when you are designating a target
only. Additionally, when dragging a module, we do not want the
footprint's pads to be used as targets for snapping.
Fixes: lp:1814402
* https://bugs.launchpad.net/kicad/+bug/1814402
Snapping to item options were partially disconnected when unifying
framework. This re-attaches the options and adds the additional option
for graphical items.
Fixes: lp:1801377
* https://bugs.launchpad.net/kicad/+bug/1801377
Rather than selecting an arbitrary track to snap, we select the closest
track to our point, allowing the via to be placed along the full track
length.
Fixes: lp:1813324
* https://bugs.launchpad.net/kicad/+bug/1813324
Prior to placing the via, we check if the resulting via will pass too
close to different nets on different layers.
Fixes: lp:1718827
* https://bugs.launchpad.net/kicad/+bug/1718827
When creating the zone cutout, we delete the old zone and add a new one
with each cutout. This requires resetting the source zone and clearing
our previous selection if we would like to continue using the cutout
tool on the new zone.
Fixes: lp:1812339
* https://bugs.launchpad.net/kicad/+bug/1812339
There is some odd interaction in the default copy constructor for
TOOL_EVENT using boost::optional under gcc. Avoid this by explicitly
constructing the event needed for cut
Fixes: lp:1812848
* https://bugs.launchpad.net/kicad/+bug/1812848
- Added ignore netcode option to CONNECTIVITY_DATA::GetConnectedItems()
- PlaceModule() now ensures the module added to the board (and thus to the connectivity database) has correct bounding box necessary for R-trees to work
- Use recursive connected pad search so that the new net is propagated to all pads
Fixes: lp:1787961
* https://bugs.launchpad.net/kicad/+bug/1787961
When renumbering pads, you can click on a pad the second time to restore
the pad to its original value. This did not allow a user to then place
the removed number on the correct pad (assuming a mistake). This commit
ensures that removed pad numbers are remembered and allow the user to
place in the correct pad.
The local/dynamic ratsnest needs to calculate on a per-pad basis as the
module is always listed as having a visible ratsnest. This fixes the
finalized ratsnest viewed when routing as well as the show local
ratsnest regression.
Fixes: lp:1811010
* https://bugs.launchpad.net/kicad/+bug/1811010
Frame refresh in wxWidgets sets the focus back to indeterminate state
and prevents hotkey action until the focus is captured again. Using
canvas update is the correct method to update the canvas display after
modifying zones/similar
Fixes: lp:1810993
* https://bugs.launchpad.net/kicad/+bug/1810993
When routing in high-contrast mode, the user may wish to place items
that are primarily on a different layer while remaining in high contrast
mode. This fixes a regression from 4.0.7
Fixes: lp:1804309
* https://bugs.launchpad.net/kicad/+bug/1804309
Moving pcbnew error strings that may be seen by the user to translated
strings. Strings that denote unexpected cases are moved to debug logs
as they are essentially asserts that should never be shown. The
exceptions are the messages shown when files are loaded. All unknown
items should show an error here.
Checks for ratsnest enabled prior to calculating and displaying the
local/dynamic ratsnest. Calls the ratsnest clear from selection clear
Notably, it appears that the tool actions do not chain transitions for
the same event. So only a single action (first specified) will be
executed when an event fires unless the actions are executed by separate
tools.
Fixes: lp:1809752
* https://bugs.launchpad.net/kicad/+bug/1809752
This fixes the handling of align/distribute tool when called on locked
items. Locked items cannot be moved but they may be used for the target
of an align/distribute operation.
Fixes: lp:1808238
* https://bugs.launchpad.net/kicad/+bug/1808238
Instead of a nag screen for locked items, we allow first the unlocked
items to be deleted and then, with a repeated request, the locked items.
This adds a popup cursor window informing the user of the option for
repeating the delete
Fixes: lp:1806507
* https://bugs.launchpad.net/kicad/+bug/1806507
Simply calling it Alternative Delete was hiding its behavior. This gives
a descriptive tooltip and command name allowing users to more easily
find the equivalent to the "Ripup" command
Graphic lines and polygons are drawn to fit specific areas for which it
is helpful to have the endpoint controlled by the cursor even when
constraining the angle.
Fixes: lp:1805502
* https://bugs.launchpad.net/kicad/+bug/1805502
* Do not compile dxf old files.
* import gfx, gal mode: make absolute placement working.
* Import gfx in legacy canvas: use it and make interactive placement working
* Take imported line width in account. Ensure DXF line thickness is OK.
* handling empty files in legacy mode.
The client filter might add items in the case where locked pads are
filtered. We need to handle this case when requesting selection by
adding new items to the m_selection
Fixes: lp:1802686
* https://bugs.launchpad.net/kicad/+bug/1802686
When we draw a path, we usually want to close the path when clicking on
the end of another line. This uses grid helper to ensure this
progression happens as expected.
When updating the status of the ratsnest, we mark its target layer as
dirty to ensure the revised data are used to draw/clear the ratsnest
Fixes: lp:1800301
* https://bugs.launchpad.net/kicad/+bug/1800301
(cherry picked from commit 50eedcf0b3)
The ratsnest layer needs to be always enabled in GAL rather than taken
from the board settings. This also adds a finalize handler to the
picker tool that allows a picker-caller to perform a specific action
when the picker tool exits. In this case, we use it to clear the local
ratsnest selections back to the default.
Fixes: lp:1800301
* https://bugs.launchpad.net/kicad/+bug/1800301
(cherry picked from commit c0d9b9ab81)
When the local ratsnest tool is used, it should toggle the state based
on the global ratsnest visibility. After changing state, the layer
cache is marked as well.
Possibly related to lp:1800301
(cherry picked from commit 22fbf30f22)
Distinguish between the snap-from and snap-to items. Previously, we
used the SELECTED or DRAGGED flags but the flagging arcitecture was
inherently fragile. This specifies items directly that should not be
used as snap targets.
Fixes: lp:1802795
* https://bugs.launchpad.net/kicad/+bug/1802795
Filtering based on selection ignores the use case where we are measuring
to a selected item. This utilizes the dragged flag to prevent snapping
based on the current state of the item drag.
Fixes: lp:1801089
* https://bugs.launchpad.net/kicad/+bug/1801089
When snapping, we should allow any point identified as a snappable
point. The additional consideration for corners might be used for
alignment in the future.
Fixes: lp:1802741
* https://bugs.launchpad.net/kicad/+bug/1802741
Separate out zone edges (which are quite specific, and should
win over most other things) from zone fills (which are pretty
generic and should only be considered when there's nothing else).
Also excludes zone fills when the zones aren't being shown as
filled.
When processing the selection filter, items were deselected before being
reselected after passing through the filter. This adjusts the logic to
only deselect those items that are filtered out.
Refactor the polygon event loop into its parent function to allow access
to the params structure. Active layer now updates the drawing layer for
add/cutout zones.
Fixes: lp:1797483
* https://bugs.launchpad.net/kicad/+bug/1797483
When using the board edit, align tool automatically moved footprints
instead of pads but distribute tool did not. This standardizes the
behavior.
Fixes: lp:1796997
* https://bugs.launchpad.net/kicad/+bug/1796997
If the user is carefully selecting the zone edge, we do not filter the
zone preemptively from our disambiguation list in the same manner as we
do for selecting on zone copper.
Fixes: lp:1796719
* https://bugs.launchpad.net/kicad/+bug/1796719
Disabling the grid should leave the snapping in place. But our disabler
returned the current point as closest, effectively always ensuring the
cursor position was the closest snap. This only uses grid when
requested.
This is temporary until we figure out a way to do multiple constraint
handling in GRID_HELPER or the EC_* class. This will work as long as
the EC constraint helper places the endpoint on either the primary or
aux grid.
Fixes: lp:1796540
* https://bugs.launchpad.net/kicad/+bug/1796540
Get the board settings when changing the drawing layer. These include
default line thickness that should be updated.
Fixes: lp:1796489
* https://bugs.launchpad.net/kicad/+bug/1796489
When drawing the crosshair should track the element while the mouse
provides the position to calculate the next snap.
Fixes: lp:1796524
* https://bugs.launchpad.net/kicad/+bug/1796524
The dimension tool is used to measure physical dimensions on the board
therefore it should be able to snap to any other object, not just those
on its own layer set as is the case for other items.
This also deals with a corner snap case for constraints by first
snapping, then constraining, then aligning to grid. This ensures OoO
for alignment from least to most constraining.
When considering potential targets for snap points, we need to exclude
the currently selected item as this will mean that we always snap to
ourselves when editing an existing item.
Fixes: lp:1796507
* https://bugs.launchpad.net/kicad/+bug/1796507
When drawing segments, the segment will be NULL'd after committing, at
which point we lost our snap layer. Choosing snap layers from the
current drawing layer is a more robust method.
Fixes: lp:1796467
* https://bugs.launchpad.net/kicad/+bug/1796467
Deselection by clicking on a zone makes working with plane zones easier
by allowing the selected item to de-selected by clicking on a zone.
Once the selection is cleared, the zone may be re-selected as normal.
Clicking on non-zone items while a separate item is selected will still
select the new non-zone item without requiring a second click.
This shows the snap indicator even when the item we are snapping to
occurs on a grid point, giving the user an indication that the point is
correctly connected.
Many items require precise, non-grid movement. Adding the ability to
flag a non-grid option will permit this behavior.
This is a required precursor commit to fixing lp:1738818 and lp:1771683
The computeAnchors function is used to find best drag locations for
items being moved. All movable PCB items should be handled.
Fixes: lp:1794304
* https://bugs.launchpad.net/kicad/+bug/1794304
When requesting to move a footprint based on the pad, the pad layers
should determine the snapping. This extracts layers from the selected
pad before allowing the filtering for locked pads
Fixes: lp:1787627
* https://bugs.launchpad.net/kicad/+bug/1787627
Since we are handling snapping in the grid helper, we don't need to
enable it in the cursor position return. This allows the grid helper to
use the frame position while optionally snapping to segments.
Put the cursor and pan control TOOL_ACTIONs in ACTION,
and refer to them in that way.
The handlers are currently identical in Pcbnew and Cvpcb,
and Gerbview (and all canvases) can benefit from them as well
if they are in libcommon. Also saves duplicated code.
Fixes: lp:1795855
* https://bugs.launchpad.net/kicad/+bug/1795855
This ensures that when starting to draw a zone or graphic element, the
preview is drawn in the same color/on the same layer as the element that
will be created. Previously, beginning a graphic polygon while a copper
layer was active would result in the preview being drawn in the color of
the active copper layer.
Polygon corners were enabled in the footprint editor but the logic
didn't extend to the board editor. This revises the logic to look for
DRAWSEGMENTs and only reference the PCB_MODULE_EDGE_T where needed to
create a new segment in the footprint.
Fixes: lp:1782966
* https://bugs.launchpad.net/kicad/+bug/1782966
Allows selection of polygons and zones by their visible area. Will only
select polygons/filled areas when they are unobstructed by other
elements in the footprint/pcb. Also adds a "skip heuristics" modifier
key for clicking (ALT) that allows the full disambiguation list to be
displayed without removing less-likely elements. This dovetails the
zone/polygon selection as it allows selecting even when areas a fully
overlapped.
Fixes: lp:1753153
* https://bugs.launchpad.net/kicad/+bug/1753153
SEGZONEs are no longer created by pcbnew but may exist in older boards.
This allows deleting the old fills in a manner similar to the deletion
in Legacy canvas.
Fixes: lp:1794571
* https://bugs.launchpad.net/kicad/+bug/1794571
SEGZONE types were confusingly named PCB_ZONE_T. Zones in pcbnew are
now _only_ PCB_ZONE_AREA_T, so we name segzone types PCB_SEGZONE_T to be
clear.
This also removes processing of the SEGZONEs from connectivity
calculations.
Unselecting performs two functions: unselecting and unhighlighting.
Some items may be deselected but still live in the temporary highlighted
layer (e.g. selecting a footprint and exchanging it). Since there is no
harm in unselecting an unselected item, we can allow it to proceed
without the check.
Commit efdbc91e42 broken the primary
alignment mechanism for maintaining the current point as an auxilliary
grid reference. This reverts that commit and fixes both the initial
issue and the associated bug by applying the primary constraint after
the secondary. In this way, we consider the secondary constraint as an
additive rather than alternative constraint.
Fixes: lp:1793888
* https://bugs.launchpad.net/kicad/+bug/1793888
When editing the pcb, Ctrl-Click will highlight a net. This allows
de-highlight with the ESC/cancel action from the selection tool. Inside
the highlight tool, ESC reverts to the selection tool while keeping the
net highlighted.
Fixes: lp:1793842
* https://bugs.launchpad.net/kicad/+bug/1793842
This is a boyscouting commit to standardize the threading of zone fills.
We do not need to join threads after their completion, instead we simply
allow them to clean up their memory without blocking the user. This
also sets the maximum number of threads that may be created to the
number of zones being filled. More than this will only leave un-used
threads being created and immediately killed.
We also include the connectivity search as a phase in the fill progress
reporter. This was the case before but did not utilize the correct
maxsize, leading to stalled progress bar.
Repeating find with the same search string would result in a not found
error for absolute search strings. Don't clear the found item if the
search string did not change from the previous search..
Fix another minor bug where the do not warp mouse pointer option was
always checked when the find dialog was called from one of the gal
canvases.
Fixes lp:1793300
https://bugs.launchpad.net/kicad/+bug/1793300
We had been deselecting items after calling edits to be safe in case the
item was deleted/exchanged by the edit. The item pointer itself remains
valid even when deleting as it is assigned to the undo stack. But it
should not remain visible or selected on the schematic if it is removed.
This tests for removed items by checking whether it (in the case of
first-level BOARD_ITEMS) or its parent (in the case of footprint item
components) remain in the view list after editing. If they are still in
the view list, then we re-select them.
( cherry-picked from 2c6d0ffe2 )
Fixes: lp:1765774
* https://bugs.launchpad.net/kicad/+bug/1765774
Fixes: lp:1775946
* https://bugs.launchpad.net/kicad/+bug/1775946
Allow corner adding to polygons in both module editor and board editor.
The board editor was already allowed but only through special types.
The module editor is now sychronized to the same process and both
recognize standard context menus
Fixes: lp:1782966
* https://bugs.launchpad.net/kicad/+bug/1782966
( cherry-picked from 06ac172c2 )
When constraining moves, the cursor snaps to grid but does not
represent the position of the final edited point. The point is rotated
to the nearest snap angle, while the vector length remains unchanged
resulting in a line longer than intended and off-grid.
This adds a grid-snap after the constraint is applied.
Fixes: lp:1792655
* https://bugs.launchpad.net/kicad/+bug/1792655
( cherry-picked from e7c51a6a6 )
Normally working at a zoom level when a footprint is not fully displayed
indicates that the user modifies other components. Selection Tool used
to discard footprints that had area larger than the viewport area, but
it may make sense to select them if there are no other candidates.
Fixes: lp:1789578
* https://bugs.launchpad.net/kicad/+bug/1789578
This allows full copper connections even when THT changes a trace layer.
It avoides selecting the actual pad to prevent actions on the copper
connections from affecting the footprints as well.
Fixes: lp:1789807
* https://bugs.launchpad.net/kicad/+bug/1789807
Text can be included in the same selection group as the parent module.
Thus if we clear the selection marker on a module's child elements we
also need to remove the element from the selection group.
Fixes: lp:1789418
* https://bugs.launchpad.net/kicad/+bug/1789418
Using Title + Message wasn't working for all the dialogs which
did substitutions in the message (which was a lot of them).
Fixes: lp:1789348
* https://bugs.launchpad.net/kicad/+bug/1789348
Also fixes a bug where nets wouldn't get changed because the
pads weren't changed and so the pad nets would propagate and
wipe out the changed nets on the tracks.
Also includes warning dialogs that pad nets will be changed if the
track nets are.
Fixes: lp:1779854
* https://bugs.launchpad.net/kicad/+bug/1779854
Use standard Magnetize() to handle grid and magnetic pads.
Use the standard menu from PCB_TOOL. Delegating the menu to
the SELECTION_TOOL just caused grief.
Also brings clients (such as Position Relative To) into line,
and implements better Cancel behaviour.
Also improves visibility of modal status messages:
- moves Select Anchor message from status bar to popup
- moves Select Reference message from dialog to popup
Fixes: lp:1786727
* https://bugs.launchpad.net/kicad/+bug/1786727
New algorithm more targetted and just clears the items. This
also obviates the need for the aQuietMode flags.
Only fixes one part of the bug, but the "fixes" line is the
easiest way to get a link in the bug to the commit.
Fixes: lp:1786727
* https://bugs.launchpad.net/kicad/+bug/1786727
This makes zoom automatique work much better in the footprint
editor, and should improve other things which probably assumed
the bounding box included everything (such as refresh code).
Callers which still want just the module outline should call
GetFootprintRect() instead of GetBoundingBox().
Some other tools (in this case the POINT_EDITOR) aren't good
citizens and activate themselves when receiving selection
changes.
Fixes: lp:1785781
* https://bugs.launchpad.net/kicad/+bug/1785781
Adds a hotkey to the TOOL_ACTION, and also checks for
action validity prior to running the actions (previously
implicitly gated by the enablement of the menu item).
Also fixes some interactivity issues in the microwave tools around
single-click tools that have initial properties dialogs. Those
need to act kind of like a hybrid between single-click and two-click
tools.
Fixes: lp:1751381
* https://bugs.launchpad.net/kicad/+bug/1751381
When changing elements in the module editor, each element shares the
same parent. Undo commits store a copy of the parent as it existed
before the change. For footprints with many elements, this creates
large, slow undo commits as a copy of the full footprint is stored for
each element being edited.
This keeps a single copy of the footprint in the undo stack per edit.
Fixes: lp:1780526
* https://bugs.launchpad.net/kicad/+bug/1780526
This introduces a new util function in geometry_utils which snaps a vector
to axes or 45 degree lines. This can be used whenever you want to
snap a vector to these angles, but still want it to stay on a grid.
This snapping is used for the dimension tool and the ruler tool.
This is substantially simpler for two-point tools that the method
used by the line tool, which uses DIRECTION_45.
Fixes: lp:1780826
https://bugs.launchpad.net/kicad/+bug/1780826
Also includes a bunch of changes to simplifiy the terminology
and unify the copper, non-copper and keepout versions.
Also removes some legacy features:
Removes contol for fill method. If the fill method is currently
segments the dialog will ask if you want to convert to polygons
on OK.
Removes control of boundary resolution. We've done this with trig
since 5.0.
(cherry picked from commit 487aaeb)
... and GetMsgPanelInfo.
Step 4 in the g_UserUnit eradication effort.
Also removes a couple of conversion routines that were close
enough to extinction.
(cherry picked from commit c75da51)
This not only reduces the number of different mechanisms, but
will also reduce (yet again) the number of Clarify Selection
pop-ups (because the CLIENT_SELECTION_FILTER runs before the
pop-up, while SanitizePads ran after it).
Fixes: lp:1710451
* https://bugs.launchpad.net/kicad/+bug/1710451
(cherry picked from commit e50a993)
The general idea is to support user-units inheritance. The
UNIT_BINDER allows wrapped controls to inherit units from their
parent dialog, while KEYWAY_HOLDER and DIALOG_SHIM allow child
KEYWAY_HOLDERs or DIALOG_SHIMs to inherit units from their
parent.
The GetUserUnits() method signature has to move to KEYWAY_HOLDER
rather than KEYWAY_PLAYER (where it makes more sense) as it’s the
only common ancestor of KEYWAY_PLAYER and DIALOG_SHIM.
As long as we'll be using the UNIT_BINDER more widely, it also
makes sense to move evaluation and validation into it.
This commit also provides eeschema’s DIALOG_LABEL_EDITOR and
pcbnew’s DIALOG_TRACK_VIA_PROPERTIES and DIALOG_SET_GRID as
models of how to use the new user-units inheritance, eval, and
validation.
Fixes: lp:593795
* https://bugs.launchpad.net/kicad/+bug/593795
(cherry picked from commit c8bc53e)
The old item pointers (which aren't safe to keep around) were
removed in favour of opaque references (void*) which are then
compared against existing items when needed.
Also improves brightening by brightening the whole footprint
(ie: its pads, drawings, reference and value) rather than just
its target cross.
(cherry picked from commit 30e90b0)
The local ratsnest needs to be able to hide as well as show visibility.
Clicking a module will toggle the visibility while clicking off all
modules clears the local ratsnest display.
Fixes: lp:1531332
* https://bugs.launchpad.net/kicad/+bug/1531332
The assert in the title line verifies that an item does not belong to
any DLIST when it is being added to one. Items in clipboard are already
owned by DLISTs, therefore they need to be removed from the original
DLISTs before being added to new ones.
Commit 72b49acc changed behavior of MODULE::ViewBBox(),
which now includes text fields area. This caused problems
with selecting footprints with relatively large text fields.
This patch fixes this problem by using MODULE::GetBoundingBox instead.
Fixes: lp:1776942
* https://bugs.launchpad.net/kicad/+bug/1776942
There's no risk in measuring an empty footprint but there's no benefit
either. This matches the measure tool to the other, deactivated
footprint tools.
- fixed via bounding box calculation in TRACK::GetBoundingBox()
- moved clearance to TRACK::ViewBBox()
- modified the Selection Tool to use EDA_ITEM::GetBoundingBox() rather
than VIEW_ITEM::ViewBBox() to determine selection
Fixes: lp:1776314
* https://bugs.launchpad.net/kicad/+bug/1776314
New items just being placed on the board are still temporary. Although
we can modify their orientations/positions, we can't stage these changes
for undo/redo without corrupting the undo stack.
Fixes: lp:1776312
* https://bugs.launchpad.net/kicad/+bug/1776312
Previously, the "Select Connection" sub-items were greyed out when the
selection contained both tracks and vias. This meant that you couldn't
access "Select Copper Connection" when the selection contained both
tracks and vias (though the keyboard shortcuts did work).
Change to use SELECTION_CONDITIONS::OnlyTypes( GENERAL_COLLECTOR::Tracks
) to allow any combination of track elements to be selected.
Fixes: lp:1772249
* https://bugs.launchpad.net/kicad/+bug/1772249
A perfect solution would create holes in the coverage map
for the zone edges and handles, but that's a lot more
work.
Fixes: lp:1773204
* https://bugs.launchpad.net/kicad/+bug/1773204
The SELECTION is a std::set. Numerical dereference of item n is O(n) as
the iterator is not random access. Therefore, a for loop using
numerical dereference is O(n!) and quickly slows.
We avoid this by storing items to remove separately while iterating and
then removing the items after we complete.
Fixes: lp:1692081
* https://bugs.launchpad.net/kicad/+bug/1692081
If you select a track with many segments (e.g. a length-tuned track) and
then select all connected items again ('U' -> 'U'), we would iterate
over all items in the selection and mark connections for each of the n
segments n separate times.
We avoid this by using the marked flag to show when the segment has
already been visited by the routine. This means that if the segment has
been checked for connections because it was connected to the previous
item, it won't be checked for connections again. However, a selection
that interleaves items from multiple connection segments will still
(potentially) be multiply checked as the BUSY flag is cleared each time
there is one not-BUSY track in the selection.
Circles are defined by center and a point on their edge. This requires
the user to do extra math to figure out the size of the circle. The
patch allows the user to edit and draw circles using radial coordinates.
This allows the user to selectively disable the snap-to behavior when
placing stand-alone vias. Full solution will require an update to the
segment distance calculation that takes into account the rounded line
caps.
Fixes: lp:1769523
* https://bugs.launchpad.net/kicad/+bug/1769523
Also fixes a bug where a FOOTPRINT_EDIT_FRAME was being passed
in to a PCB_EDIT_FRAME.
Also tidies up Modedit settings handling for settings which can't
be edited in Modedit's preferences dialog. They're now copied
from Pcbnew.
Fixes: lp:1768477
* https://bugs.launchpad.net/kicad/+bug/1768477
Duplicate already works, so there's little reason to disallow
using the zone dialog to do it.
The legacy canvas can't be fixed because we'll immediately
union the two zones, resulting in a no-op.
Fixes: lp:1464677
* https://bugs.launchpad.net/kicad/+bug/1464677
This really needs to get put into the VIEW_CONTROLS for all the
tools, but that's probably a bit too risky for 5.0 at this
point.
Fixes: lp:1766547
* https://bugs.launchpad.net/kicad/+bug/1766547
If the initial pad was a custom pad converted in a usual pad + graphic items by the command:
"Explode Pad to Graphic Shapes"
the "old" primitives were not cleaned, and the new created pad contained these old primitives, regardless the new selected shapes.
(Usual case when a user want to edit a custom shape)
When multiple cut commands were issued, the cut command handler would
restart multiple times and keep running until the handler that was
invoked first finishes. As all handlers kept a selection copy, they
would try to save the deleted items to the clipboard resulting in a
crash.
Fixes: lp:1761221
* https://bugs.launchpad.net/kicad/+bug/1761221
Previous implementation refilled zones every time they have been
unselected. This patch adds a flag that tracks whether the
zone has been actually modified, so it will be refilled only when
necessary.
Fixes: lp:1760903
* https://bugs.launchpad.net/kicad/+bug/1760903
- vias were always left selected, include vias in tracks filter - as in legacy
- make text filtering work
- cleanup drawings filtering code
- hide checkbox "Include items on invisible layers" because it does not work in GAL
CTRL+{X,C,V} used to be handled both by the legacy hotkey system that
generated ID_EDIT_{CUT,COPY,PASTE} wxCommandEvent, and the Tool Framework
hotkey system.
Fixes: lp:1749549
* https://bugs.launchpad.net/kicad/+bug/1749549
When aligning module centers, it can be hard to determine which item
will be chosen for the alignment target when it chooses based on the
median of the center values. Instead, this patch chooses the alignment
target as the top and left most items of the Y and X centering,
respectively
When aligning in pcbnew, check for pad/module locks before performing a
move and query the user.
When aligning on pads, don't move the pad without moving the footprint,
so we don't break footprints.
Fixes: lp:1751352
* https://bugs.launchpad.net/kicad/+bug/1751352
reimplement the centerpoint distribution and use it when the items to be
distributed overlap leaving no gap to use for spacing
Fixes: lp:1748763
* https://bugs.launchpad.net/kicad/+bug/1748763
Also adds indicators in layers palette for feedback.
Also generates sized images for all indicators instead of using
scaled bitmaps (which didn't look great).
Also fixes a completely unrelated typo in a UI string.
Includes some dialog changes to go with the menu update.
Includes promoting the Pcbnew graphics mode back to main menu.
Includes renaming Graphics modes to Toolsets.
NEW: add new align icons based on the existing align_items.svg icon, just flipped and rotated
CHANGED: change the context menu to use the new align icons
Tools preserve their state between runs, so it could happen that
activating a tool restores the state when autopanning is enabled, even
though it should not be.
Commit complementary to 4f0c9b6b. In case there were multiple tracks
under the cursor, disambiguation was shown twice because
SELECTION_TOOL::selectConnection() cleared the selection and requested
it again.
Also adds Cancel context menu items for Place Footprint,
Place Target, Place Drill Origin and Place Grid Origin tools,
as well as the standard Zoom and Grid choices.
Removes the Paste context menu item from the Place Drill
and Place Grid Origin tools.
Fixes: lp:1568396
* https://bugs.launchpad.net/kicad/+bug/1568396
Second disambiguation menu was caused by another call to
SELECTION_TOOL::RequestSelection() meant to get the list of
connected tracks. When there were only footprints under the cursor,
it asked the user again to pick an item to remove.
Fixes: lp:1748521
* https://bugs.launchpad.net/kicad/+bug/1748521
This changes the distribute horizonally and vertically tools to place
items with constant gaps between them. The previous implementation put
item centers evenly apart but thereby ignored the relative width and
height of the items (i.e. wide items appeared closer together than
narrow items).
Fixes lp;1745366
https://bugs.launchpad.net/kicad/+bug/1745366
Using footprint rects instead of the larger bounding box means that
reference and value texts no longer influence the positioning of the
footprint in unexpected ways. Treatment of non-module items is
unchanged.
Launching right click context menu overrides the cursor position, so all
actions executed by the tools will be performed in the right click
position. It created an issue, as the overridden cursor settings were
saved into wrong context if there was another tool activated in the
meantime.
Current implementation saves cursor settings for all tools and restores
them once the right click context menu disappears.
Fixes: lp:1745981
* https://bugs.launchpad.net/kicad/+bug/1745981
Fixes: lp:1746507
* https://bugs.launchpad.net/kicad/+bug/1746507
PICKED_ITEMS_LIST knows the architecture of the undo commands so
that it can delete those ITEMs which it owns. This represents poor
encapsulation so instead of adding yet another case, I added a
UR_TRANSIENT item flag which is set by callers whenever they create
new objects to “give to” the undo/redo stack. This allowed some
cleanup of other code, but cleaning up UR_DELETE and UR_WIRE_IMAGE
will be a bigger task and have to wait for another day.
Fixes: lp:1542018
* https://bugs.launchpad.net/kicad/+bug/1542018
The undo/redo operations are essentially the same as for
UR_CHANGED: we store both the origin marker item and a copy
of it and flip back and forth between the two. This also
required the implementation of clone() for the markers.
The ORIGIN_VIEWMARKER is moved from being a subclass of
EDA_ITEM to BOARD_ITEM to facilitate the use of a UR_CHANGE-
like implementation without having to know the internals
of the ORIGIN_VIEWMARKER.
In the command processors, the setting of the origins is
broken into two parts: one for UI-level access which includes
setting up undo, and one for low-level access which does not.
The undo/redo code itself of course uses the lower level.
Fixes: lp:1542018
* https://bugs.launchpad.net/kicad/+bug/1542018
This commit also adds a no-selection-mode, which allows the user
to specify what gets update (through the various match modes).
The no-selection-mode is accessed via the Edit menu, although
it could also be applied to the context menu.
Fixes: lp:1466857
* https://bugs.launchpad.net/kicad/+bug/1466857
Rename GetPolyPoint() to BuildPolyPointsList(), because GetPolyPoint() looks like an accessor, but it is not an accessor.
(Using it as accessor can creates a *very long calculation time* for very basic access to polygon vertices)
Fixes: lp:1745050
https://bugs.launchpad.net/kicad/+bug/1745050
Fix also option tool "show footprint texts in outline mode" code,
but because there is no code to show texts in outline mode in GAL canvas, this option still works only in legacy canvas
When a rotation/flip command was issued when a newly placed text
was hovering over an existing item - the item underneath would be
affected by the command and the new text would be discarded.
Fixes: lp:1744152
* https://bugs.launchpad.net/kicad/+bug/1744152
Some actions, such as select trivial connection, don't need the
user to choose which trace at a corner to start from -- either
one will do. Same for moving a simple trace corner.
Likewise, Edit in Footprint Editor shouldn't ask if you mean the
footprint or the pad. Obviously it's the footprint.
This change adds a CLIENT_SELECTION_FILTER which allows clients
to do tool- or action-specific filtering of the selection before
the disambiguation menu is run.
It also removes some tool- and action-specific code which was
in the selection_tool and shouldn't have been.
Fixes: lp:1708869
* https://bugs.launchpad.net/kicad/+bug/1708869
If the client tool indicates it isn't happy for us to continue
(because, for instance, the user has cancelled the Zone Properties
dialog), then make sure we don't capture the mouse.
Fixes: lp: 1740780
* https://bugs.launchpad.net/kicad/+bug/1740780
This patch adds functionality to the Pcbnew draw tool to show the dx and
dy of the current segment being drawn if the relative origin (pressing
spacebar) is not already set (i.e. if those coordinates are ( 0, 0 ) ).
You can set the relative origin while using the draw tool by pressing
spacebar. The relative origin is reset on exit of the tool.
fixes: lp:1736133
* https://bugs.launchpad.net/kicad/+bug/1736133
Improved the selection heuristics to keep footprints in the
disambiguation menu when they contain pads with high pad-to-footprint
area ratio.
In other words: make it possible to select a footprint when
most of its area is taken by a pad. Previously pads were given the
priority, so it was very tricky to select the parent footprint.
Fixes: lp:1739425
* https://bugs.launchpad.net/kicad/+bug/1739425
To avoid situations when a large footprint covering most of the board
area (e.g. shield connector) is always selected, even when user clicks
in a seemingly empty spot, a simple filter has been added. In case
the footprint area covers more than 90% of the view area, the large
footprint is not selected. This way large footprints do not disturb
editing when the zoom is high enough.
Fixes: lp:1636214
* https://bugs.launchpad.net/kicad/+bug/1636214
Module placer did not mark the newly placed modules as selected,
but all edit functions (rotate/place/etc.) rely on getting a selected
item. When a rotation/flip command was issued, the newly placed module
was dropped and the one underneath the cursor has been rotated.
To fix this the newly placed modules are marked as selected.
It also simplifies the placer code a bit.
Fixes: lp:1738148
* https://bugs.launchpad.net/kicad/+bug/1738148
If the object changes between a TA_CONTEXT_MENU_UPDATE
event and a TA_CONTEXT_MENU_CHOICE event (usually as
a result of a cancel), the old code would leave the
last item hidden.
Fixes: lp:1737562
* https://bugs.launchpad.net/kicad/+bug/1737562
Opening Properties dialog normally does not ask the user to confirm the
action, even for locked items. The exception was a case when there was
nothing selected and Properties dialog was invoked via its hot key -
then SELECTION_TOOL::RequestSelection() tried to get the item under the
cursor, verifying the lock flag.
Fixes: lp:1734537
* https://bugs.launchpad.net/kicad/+bug/1734537
A change in commit 5731000135 caused kicad to stop allowing users
to move items like footprints, arcs and lines using anchors other
than the center point.
This was caused by the new code that stores reference points for
clipboard pasting, a call to updateModificationPoint() prevented
some old code paths from executing, which caused the selection to
snap into the cursor, always using the center anchor.
This fix moves the call within the if-cases that need it, and adds
a ClearReferencePoint call when the selection is "dropped" to allow
the user to grab the same selection again from a different anchor.
Fixes: lp:1722512
* https://bugs.launchpad.net/kicad/+bug/1722512
- renamed connectivity.[h|cpp] to connectivity_data [.h|.cpp] so that the file name matches the main class name.
- GetNetItems() now returns a vector instead of a list
SHAPE_POLY_SET: fix crash in VertexCount when it is a empty poly set, or when params are incorrect.
minor other fixes:
warning in degug mode in dialog_dxf_import_base.cpp
pcb_painter.cpp: remove a useless debug line.
- fixed netcode propagation bug
- factored out EDIT_TOOL::m_offset, now selection offset is stored in SELECTION class
- added VECTOR2I-based Move/Flip/Rotate methods in BOARD_ITEM
- added selection of reference point
- added snapping when pasting
- some minor code refactoring
- disabled pasting between footprint and pcb editors due to model incompatibility
-Can paste items from board to module-editor (only module parts)
-Can paste entire modules just as copy
-Can copy items inside module-editor
Known limitations:
-Will crash if trying to paste a module containing module_text inside
the module editor ( dont know why, problem existed before )
-If copying things with strange layer names, the layer names will be
changed.
Now the heirarchical sheet selection feature includes tracks that belong
to a net spanning multiple sheets, but only by doing a logical connection
from the pads of the modules. This is to be able to select connections
between components on the same sheet. For example if the sheet contains a
star power connection or something similar, then most of the sheet local
connections will now also be included.
- support for background color setting
- removed several global config settings (such as g_Drc_On)
- wrapped most of global config settings in PCB_GENERAL_SETTINGS class
- reorganized PCB general options dialog to clearly mark which options concern only the legacy canvas
- new GAL feature for legacy users: double-click (or E) to change track width available as an option.
Fixes: lp:1530543
* https://bugs.launchpad.net/kicad/+bug/1530543
Fixes: lp:1707145
* https://bugs.launchpad.net/kicad/+bug/1707145
- added TOOL_INTERACTIVE::resetTransitions()
- made protected and moved TOOL_BASE::setTransitions() to TOOL_INTERACTIVE
- TOOL_MANAGER calls TOOL_INTERACTIVE::resetTransitions() instead of
setTransitions()
This issue is due to an unexpected behavior of evt->IsClick( BUT_LEFT ) used in this method,
which detect a mouse release button and not a mouse click down.
Fixes: lp:1700197
https://bugs.launchpad.net/kicad/+bug/1700197
This patch does the following:
* extracts a method to determine the anchor point of the move
* improves the logic of the anchor point determination for selections of multiple objects which do not contain footprints
In the previous version the method did not work correctly
when an action was invoked from context menu. In such case,
the cursor position was obtained in the moment of selecting
the action, instead of using the right click location.
- ratsnest is updated now when undoing in legacy view
- select whole net regression
- local ratsnest in the GAL regression
- pick correct zone net for stitching vias
- mark nets as dirty on net propagation to force ratsnest update
Todo:
- cleanup board algorithm is still broken
This patch adds a radiobox to allow the user to select a reference point for
the move. The additional options are: User Origin (set with <space>),
Grid Origin and Sheet Origin (effectively making it an absolute coordinate).
A checkbox is added (where it makes sense) to allow overriding which point
within the component is put on top of the designated coordinate.
Fixes: lp:1460460
* https://bugs.launchpad.net/kicad/+bug/1460460
These were backwards since internal angles are CCW due to the inverted Y
axis.
The hotkeys have NOT changed. This means 'R' is now clockwise and
'Shift+R' is anti-clockwise. This is the same as EEschema, but not the
same as Legacy mode.
Removes the need of using the legacy code in polygon/PolyLine.{h,cpp},
refactoring all CPolyLine instances with SHAPE_POLY_SET instances.
The remaining legacy methods have been ported to SHAPE_POLY_SET;
mainly: Chamfer, Fillet, {,Un}Hatch.
The iteration over the polygon vertices have been simplified using the
family of ITERATOR classes.
The zone creation in DRAWING_TOOL was a complex event loop whici
simultaneously managed the event handling, construction of the preview
polygon and the creation and commiting of the zone, all in the same
scope. This has been broken into several pieces:
* POLYGON_ITEM preview item, used to preview the polygon in progress
* POLYGON_GEOM_MANAGER is a class that collects points from user input
and used them to describe a polygon's geometry, including calculation
of 45-degree constrained leader lines
* ZONE_CREATE_HELPER is a class which deals with creating zones based on
geometry from a geometry manager and parameters from the DRAWING_TOOL
* The (much simpler) event loop in DRAWING_TOOL drives the
POLYGON_GEOM_MANAGER. With a minor refactor, this loop can be reused
in future for other polygonal tools if wanted.
The polygon preview now has a translucent fill which makes it easier to
visualise the zone.
This also adds the Close Zone Outline and Delete Last Corner actions as
part of the new event loop.
Fixes: lp:1663885
* https://bugs.launchpad.net/kicad/+bug/1663885
Fixes: lp:1667885
* https://bugs.launchpad.net/kicad/+bug/1667885
This uses the two-point geometry manager to split the logic of the ruler
geometry and the preview item display. This allows the ruler to use that
manager's angle snap feature.
The motivation here is to concentrate display options in the GAL display
settings, ready for removal of legacy canvases. Instead of having the
property as a member of the DRAW_FRAME, with the GAL canvas retreiving
it from there, it is now in the GAL_DISPLAY_OPTIONS struct, and both GAL
and legacy get it from there.
The options for setting cursor shape are then moved out of the general
options dialog, and into the GAL display options widget, where they can
be used in all GAL-aware programs.
GAL cursor shape works on GAL, but not legacy, so the option is now
available on OSX (but only affects GAL, and is labelled as such).
This adds the microwave tools to GAL in Pcbnew as a new tool:
MICROWAVE_TOOL.
Some new preview items are introduced to support this:
* TWO_POINT_GEOM_MANAGER for managing construction of two-point
geometries, such as that used to construct the inductor.
* CENTRELINE_RECT_ITEM a preview item to draw ractangle with a given
aspect ratio along a line (specified using a TWO_POINT_GEOM_MANAGER)
PCB_TOOL gets a generic event loops which should be useful for more
than just microwave tools:
* doInteractiveItemPlacement() - handles event loops that wait for a
click, create an item on click and then allow moving it
around/flipping, etc.
Fixes: lp:1531323
* https://bugs.launchpad.net/kicad/+bug/1531323
This adds a richer overlay to the arc-by-three-points tool in Pcbnew,
including more guide-lines and a live display of radius and angle.
Also included is ability to go back to the previous step (if setting end
angle, you can go back to setting start point, etc) using Backspace, and
Ctrl snaps the start/end angles to 45 degree multiples.
This adds new classes
* MULTISTEP_GEOM_MANAGER: represents a generic "geometry manager" that
builds up some geometrical construction based on a sequence of points.
Used by:
* ARC_GEOM_MANAGER: handles the logical flow of constructing an
arc by centre-point, set radius, set angle. This moves the logic out
of the Pcbnew DRAWING_TOOL event loop in drawArc().
* ARC_ASSISTANT: graphical overlay to communicate current arc shape to
the user during the drawing process
This allows to measure between features on a PCB. It uses a preview
EDA_ITEM in common, but due to the use of the IDs, it's currently
Pcbnew/Modedit only.
This also adds several "utils" for graphical functons useful when
drawing preview items on GAL canvases.
Fixes: lp:1467313
* https://bugs.launchpad.net/kicad/+bug/1467313
This simplifies the (already simple) SELECTION_AREA class. It is also
moved into KIGFX::PREVIEW and put in the common library, where it can be
reused by other GAL-aware tools (not just in Pcbnew) in future.
- The tools can now specify if the items in the selection must be editable/
deletable. This is groundwork to be able to select/delete DRC markers, which can't
otherwise be edited.
- Fixed disappearing of selected objects
BOARD::GetBoundingBox() now directly calls BOARD::ComputeBoundingBox()
and there is a new method BOARD::GetBoardEdgesBoundingBox() used for
call sites that needed to use ComputeBoundingBox( true ) in the past.
This allows COMMON_TOOLS to implement ZoomFitScreen without knowledge
of the BOARD class.
Adds a similar crossprobe as modules has in pcbnew. When clicking a
sheet in eeschema, the items that are exclusive in that scheet will be
selected in pcbnew if using the GAL canvas.
SELECTION now holds EDA_ITEMs not BOARD_ITEMs so various places had to
change to casting the selected items to BOARD_ITEMs.
Fixed compilation warnings on clang (Tom)
This just uses the same hatch lines that are built into the zone as
legacy.
They are always drawn, even when there is a fill, as if the fill
doesn't reach the corners, the hatches can be seen.
Fixes: lp:1487043
* https://bugs.launchpad.net/kicad/+bug/1487043
This is used to provide menu entries that allows cancellation of
interactive drawing and routing tools without needing the keyboard.
It is provided in the drawing tools and the router tool.
The cancel event doesn't have any new functionality (e.g. track rip-up
for the PNS router - lp:1448460), this just adds it to the menu, where
it behaves the same as an Escape keypress.
Some grid/zoom tools are left in PCBNEW_CONTROL because they currently
depend on Pcbnew-specific class members. Once refactoring is done to
make it possible to use all zoom and grid controls outside of pcbnew,
these last tools can be moved to common to match their ACTIONs.
New virtual class ACTIONS is added as a member to EDA_DRAW_FRAME so
that the TOOL_DISPATCHER can have access to the appropriate derived
version of TranslateLegacyId()
bitmaps.h was included in nearly every file in the project due to it
being included by base_struct.h
Only about 130 files actually use the XPM definitions defined there, and
many of those already included bitmaps.h themselves, or via
menu_helpers.h. However, touching bitmaps.h would result in over 400
rebuilt files for pcbnew alone.
This commit moves the bitmap-related types like BITMAT_DEF out to a new
header, which is still included by base_struct.h, which is less
avoidable for now, it's it's used in the interface.
The icon list is still in bitmaps.h. This has the side effect that's
it's now easier to automatically generate this file.
Many classes in pcbnew and eeschema needed some functions moved
to the implementaitons from the headers too.
The apply settings and push settings options now take account of the
validity of the global pad settings when deciding whether to show or
not.
Global pad push now requires a source pad and doesn't push from the
global pad setting when there is no selection.
The whole submenu is hidden when there are no enabled items.
Fixes: lp:1664016
* https://bugs.launchpad.net/kicad/+bug/1664016
This patch fixes a problem with GAL where zones are ignored in ratsnest
calculation.
The problem is that calling RN_DATA::Update on a zone with no polygons
(an unfilled zone) will remove the zone successfully, but then
RN_DATA::Add is a no-op.
From this point on, because ::Update refuses to work on items that have
not been ::Add'ed, the zone is removed entirely from ratsnest
calculation and will only be reconsidered once it is explicitly ::Add'ed
again.
The fix is to explicitly create an empty RN_ZONE_DATA object for every
zone that is ::Add'ed.
A second problem is that the point editor forgot to call
RN_DATA::Recalculate after calling Fill_Zone.
Fixes: lp:1537120
* https://bugs.launchpad.net/kicad/+bug/1537120
Modifies the selection menu to be adaptive and disable selection options
that are not possible.
Adds a new selection option that is only available when selecting
modules, this tool will select all footprints on the same sheet level or
belonging to subsheets. It will also search for nets that are only
connecting between modules on the same sheet or lower and select every
segment and via belonging to it.
This action launches the normal interactive zone tool, but re-uses the
settings from an existing zone, based on a flag passed to the main zone
function.
Break a chunk of the new zone tool out into a separate function to keep
the code clear. When zone cutouts and similar zone tools are added,
they'll get the settings from existing zones.
This commit now used std::unique_ptr for the temporary zone item, which
simplifies handling of the ownership of that item.
This commit wires up the as-yet-unused "remove alternate" tool action
and uses it to select copper connections (normally 'U') before deleting
segments.
THis also reverses the sense of Delete and Backspace (Delete used to be
'remove' and Backpace was 'remove alt', now it is reversed). This means
that backspace is the key that removes a segment and Delete removes the
track. This is the same as legacy behaviour. Other delete actions are,
for now, the same between Delete and Backspace.
Fixes: lp:1517213
* https://bugs.launchpad.net/kicad/+bug/1517213
The previous behaviour was to act on only the first item in the
selection. The new behaviour is to act on every eligible item (in this
case, tracks and vias).
Provide a visual feedback to the user how each rotation
will affect the routing by immediately reflecting the
change in ratsnest orientation.
Signed-off-by: Aurabindo J <mail@aurabindo.in>
Fixes: lp:1663488
* https://bugs.launchpad.net/kicad/+bug/1663488
This makes "rotate" into two separate TOOL_EVENTs, which each have a
"multiplier" parameter.
Also added is a namespace for 'free functions' that use TOOL_EVENT
public interfaces (perhaps with other inputs too) to centralise some
decision-making and calculations.
Fixes: lp:1660731
* https://bugs.launchpad.net/kicad/+bug/1660731
Automatically switch to a drawing layer, if a copper layer was
preselected. No annoying message boxes.
Do not deactivate the tool on layer switch.
Replaced setting updatePreview with direct calls to VIEW::update
Line width is kept in m_lineWidth for all shapes.
Import becomes apply and export becomes copy.
The term "push" to apply settings globally has not been renamed.
Swap the order of the copy and apply in the context menu.
Perviously, the generic snapping code would choose the nearest of the
module origin and origin of each module pad when selecting a module
using the "Find module" tool (T hotkey).
This is unlikely to be expected unless the cursor is already near the
correct pad or the module centre.
New behaviour is to pick up by module origin first, then
select the module. This means that the cursor is already nearest the
main module origin anchor, so that is what will be used.
Fixes: lp:1571214
* https://bugs.launchpad.net/kicad/+bug/1571214
This implements the pad import/export to the board's master pad setting
in the GAL canvases.
Implemented as a new GAL tool: PAD_TOOL.
It uses the same dialog, which has been split out into its own files in
pcbnew/dialogs, rather than along with frame methods in
pcbnew/globaleditpad.cpp.
Fixes: lp:1619304
* https://bugs.launchpad.net/kicad/+bug/1619304
Make all EDA_TEXT data private and rename accessors to avoid function
name collisions in derived classes.
Overload EDA_TEXT's SetTextAngle() and SetEffects() in TEXTE_PCB.
Add support for preserving Reference text position, size, orientation
during a netlist import into a BOARD, as well as the one off footprint
update dialog.
When creating a copy of CONTEXT_MENU, always a CONTEXT_MENU instance was
constructed, whereas an inherited type should be used. Solved with
CONTEXT_MENU::create() that has to be overridden in inheriting classes.
Event & update handlers are now virtual functions, instead of setting
the handlers with Set{Event,Update}Handler().
Since you have to explicitly enter the module editor with the menu or
hotkey, allowing editing of module sub-parts once in should not cause
any unexpected changes.
Fixes: lp:1591625
* https://bugs.launchpad.net/kicad/+bug/1591625
In principle, this patch reverts 2eefa117. The difference is removal of
one unused method (SELECTION::clear) and fixing hidden overloaded
virtual methods warnings.
Fixes: lp:1657569
* https://bugs.launchpad.net/kicad/+bug/1657569
There used to be a number of TOOL_ACTIONs that had entries both in
SetTransitions() and the event loop, which seemed redundant and
troublesome.
Now it is not necessary anymore, transitions setup is enough to execute
associated actions.
The problem with simple deleting VIEW_ITEM_DATA upon VIEW_ITEM removal was
caused by the default copy constructors that copied pointers.
Once a copy of an item was destroyed, the VIEW_ITEM_DATA has been
destroyed, effectively invalidating m_viewPrivData for the other item.
This means that non-top-level tools, for example EDIT_TOOL and
PCB_EDITOR_CONTROL can submit their own menus to the top-level tool's
TOOL_MENU, which will then retain a reference to it and make it
available for the CONTEXT_MENU that is shown.
Add a class TOOL_MENU, which provides a management class for a
CONDITIONAL_MENU and a set of CONTEXT_MENUs. The aim of this is to
provide a central place where all TOOL_INTERACTIVEs can get a "basic"
context menu that either they or other tools can register new items and
sub-menus against.
This means that "top-level" tools no longer need to manage the lifetimes
of any CONTEXT_MENUs that they add, and can also delegate simple menu
display functions.
If the SELECTION_TOOL's Select... menu is not shown, the separator under
it should also not be shown, so use the same SELECTION_CONDITIONS to
enforce this.
The GAL line segment tool now listens to the global line segment 45
degree locking preference, with Ctrl used to invert the behaviour. The
behaviour therefore follows the setting normally, and the user can
override when needed with Ctrl.
Fixes: lp:1635718
* https://bugs.launchpad.net/kicad/+bug/1635718
- Finalize transition to BOARD_COMMIT (removed all remaining uses of PICKED_ITEMS_LIST) and implicit view/ratsnest updates
- Simplified SELECTION class, it now can be directly added to a VIEW
- Removed unnecesary casts and templates
- Introduced C++11 features (range based for, lambdas) where they improve code readability
- Added non-undoable COMMITs, which can be used to propagate change notifications to interested listeners (e.g. ratsnest/view)
* Factor out PROPERTIES object from the PCB plugin code and move it into
common so it can be used by both the Pcbnew and Eeschema plugins.
* Add schematic I/O plugin manager for loading and saving schematic and
component library files.
* Add initial attempt at a parser for current schematic file format. This
parser will be infinitely more strict than the current parser which is very
forgiving in what it parses.
* Make minor changes to the base bitmap class to support the new parser.
* Add find root sheet support to sheet object to allow fetching the root
sheet from any sheet in the stack.
Following rev 6627 (git 2777182), if a non-duplicatable item was the object of
a Duplicate action, the original item would be picked up, potentially
misleading the user into thinking something was actually duplicated.
* No initial copied object changed (this was a serious bug to modify these objects. Previous version modified references and other texts using a very stupid algorithm).
It also fixes bug 1549231
* only new pads are numbered (therefore renumbering is used only in footprint editor)
* remove not working and useless feature in circular array: now only use number for pads (others options using alphabetical letters are removed: did not work corectly, and were useless)
* a more clear option is used to choose if the pads are numbered from a choosen value, or from the first avaible value
* Adding a warning messsage if a parameter is incorrect.
The standard library requires iterators passed to functions that modify the
container to be mutable iterators, but GCC's implementation accepts
const_iterator in some places where these are only used to mark a place,
but the actual modification happens through a different parameter.
As this breaks implementations that use the passed iterator to modify the
container (e.g. because they use a different data organization), this is
not portable; because we already have a non-const reference to the
container anyway, this is trivially fixed as well.
This was apparently left in from debugging earlier, and should no longer be
needed. Since it uses a GCC extension, it makes compilation on others fail.
* Fix segfault caused by invalidation of the end item by
PNS_LINE_PLACER::UpdateSizes().
* GAL zone drawing tool updates the ratsnest after zone drawing is complete.
* Fixed performance issue in zones processing using strict simplification
only for the final filled area.
jean-pierre charras
Seth Hillbrand
Tomasz Włostowski
Wayne Stambaugh
Jeff Young
Maciej Suminski
John Beard
Ronnie Gaensli
Carsten Schoenert
Andrzej Wolski
Jon Evans
Robbert Lagerweij
Michael
Camille
Jose I Romero
Marvin Schmidt
Kristoffer Ödmark
Oliver Walters
Baranovskiy Konstantin
Michael Geselbracht
Oliver Walters
Fabrizio Tappero
hauptmech
Russell Oliver
Alejandro García Montoro
Chris Pavlina
Julius Schmidt
Aurabindo J
Maciej Suminski
Nick Østergaard
Dick Hollenbeck
Simon Richter
decimad
Gustav Bergquist
Wayne Stambaugh
Simon Wells
Johannes Agricola
Cirilo Bernardo
Brian Sidebotham
Henrik Nyberg
Andrew Zonenberg
Jon Neal